FILE NAME: CP014348.scexe TITLE: HP NC-Series Broadcom Online Firmware Upgrade Utility for Linux x86_64 VERSION: 2.3.0 REVISION: 0 LANGUAGE: English CATEGORY: Software Solutions DIVISIONS: Enterprise and Mainstream Servers PRODUCTS AFFECTED: HP NC1020 Gigabit Server Adapter HP NC6770 Gigabit Server Adapter HP NC7760 Gigabit Server Adapter HP NC7761 Gigabit Server Adapter HP NC7770 Gigabit Server Adapter HP NC7771 Gigabit Server Adapter HP NC7780 Gigabit Server Adapter HP NC7781 Gigabit Server Adapter HP NC7782 Gigabit Server Adapter HP NC150T PCI 4-Port Gigabit Combo Switch Adapter HP NC320T PCIe Gigabit Server Adapter HP NC320I PCIe Gigabit Server Adapter HP NC320M PCIe Adapter HP NC324I PCIe Dual Port Gigabit Server Adapter HP NC325M PCIe Quad Port Gigabit Server Adapter HP NC326I PCIe Dual Port Gigabit Server Adapter HP NC326M PCIe Dual Port Adapter HP NC370T Multifunction Gigabit Server Adapter HP NC370F Multifunction Gigabit Server Adapter HP NC370i Multifunction Gigabit Server Adapter HP NC371i Multifunction Gigabit Server Adapter HP NC373T PCIe Multifunction Gig Server Adapter HP NC373F PCIe Multifunction Gig Server Adapter HP NC373i PCIe Multifunction Gig Server Adapter HP NC373m PCIe Multifunction Gig Server Adapter HP NC374m PCIe Multifunction Adapter HP NC380T PCIe DB Mulitfunc Gig Server Adapter HP NC382i DP Multifunction Gigabit Server Adapter HP NC382T PCIe DP Multifunction Gigabit Server Adapter HP NC382m DP 1GbE Multifunction BL-c Adapter HP NC532i Dual Port 10GbE Multifunction BL-c Adapter HP NC532m Dual Port 10GbE Multifunction BL-c Adapter HP NC105i PCIe Gigabit Server Adapter HP NC107i PCIe Gigabit Server Adapter OPERATING SYSTEMS: Red Hat Enterprise Linux 6 AS/ES for x86_64 Red Hat Enterprise Linux 5 AS/ES for x86_64 Red Hat Enterprise Linux 4 AS/ES for x86_64 SUSE LINUX Enterprise Server 11 for x86_64 SUSE LINUX Enterprise Server 10 for x86_64 PREREQUISITES: Pentium-based computer 2GB RAM minimum tg3 Linux driver version >= 3.58b bnx2 Linux driver version >= 1.4.41 bnx2x Linux driver version >= 1.45.19 EFFECTIVE DATE: 02/08/2011 SUPERSEDES: CP014056.scexe DESCRIPTION: This scexe contains the utilities and binaries for upgrading HP ProLiant Gigabit Ethernet NICs boot code, PXE, IPMI, UMP, CLP, and iSCSI code running under Linux x86_64 platform. ENHANCEMENTS/FIXES: 1) This tool does not fail anymore when upgrading UMP for NC326i 2) Displays informational messages when discovering NIC FW versions installed on the system. Table of Contents ================= Introduction Packaging Performing the Firmware Upgrade Firmware Upgrade Log Configure IPMI: Disable/Enable Introduction ============ This file describes the firmware upgrade of the HP Gigabit Server Adapters mentioned in the PRODUCTS AFFECTED section of this document. User guides and additional HP Network Adapter information can be found at: http://h18004.www1.hp.com/products/servers/networking/index-nic.html Packaging ========= The firmware upgrade utility is released in scexe format. The file is a single self-extracting executable that unpacks the component, runs it, and cleans up the component. This one-step process replaces the rpm format which would require three steps to install, execute, and remove. Performing the Firmware Upgrade =============================== 1. The utility requires the adapter interface to be up. You can bring up a network adapter interface by using the following command: # ifup ethx or # ifconfig ethx up 2. The firmware can be upgraded interactively using the following command: #./CP00xxxx.scexe 3. Before the upgrade is attempted, a copy of the firmware image is saved. If the firmware upgrade fails due to an unrecoverable error, you can restore your original firmware interactively using the following command: #./CP00xxxx.scexe -p Note: Restoring an image is currently supported on non-multifunction NICs. 4. Check the help menu for more information regarding command line options. #./CP00xxxx.scexe -h Firmware Upgrade Log ==================== The results to the firmware upgrade are in the nicfwupg.log which will be written to the current working directory. Configure IPMI: Disable/Enable ============================== 1. The utility requires the adapter interface to be up. You can bring up a network adapter interface by using the following command: # ifup ethx or # ifconfig ethx up 2. Verify the configuration status of the network adapter by sending the following command: # ./CP00xxxx.scexe -c 3. Configure IPMI by sending the following command: # ./CP00xxxx.scexe [ interface ] ipmi [ options ] options: 0 - Disable IPMI 1 - Enable IPMI example: The following command disables IPMI # ./CP00xxxx.scexe eth0 ipmi 0 Note: Please refer to the adapter QuickSpecs for information on supported features. Copyright 2011 Hewlett-Packard Development Company, L.P. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies