FILE NAME: CP016410.scexe TITLE: HP NC-Series QLogic P3 Online Firmware Upgrade Utility for Linux x86_64 VERSION: 4.0.585 REVISION: 0 LANGUAGE: English CATEGORY: Software Solutions DIVISIONS: Enterprise and Mainstream Servers PRODUCTS AFFECTED: HP NC375T PCI Express Quad Port Gigabit Server Adapter HP NC375i Quad Port Multifunction Gigabit Server Adapter HP NC522SFP Dual Port 10GbE Server Adapter HP NC524SFP Dual Port 10GbE Proliant Module HP NC510F PCIe 10 Gigabit Server Adapter HP NC510C PCIe 10 Gigabit Server Adapter HP NC512m Dual Port 10GbE Multifunction BL-c Adapter HP NC522m Dual Port 10GbE Multifunction BL-c Adapter OPERATING SYSTEMS: Red Hat Enterprise Linux 6 Update 2 for AMD64/EM64T Red Hat Enterprise Linux 6 Update 1 for AMD64/EM64T Red Hat Enterprise Linux 6 for AMD64/EM64T Red Hat Enterprise Linux 5 Update 8 for AMD64/EM64T Red Hat Enterprise Linux 5 Update 7 for AMD64/EM64T Red Hat Enterprise Linux 5 Update 6 for AMD64/EM64T SUSE LINUX Enterprise Server 11 Service Pack 2 for AMD64/EM64T SUSE LINUX Enterprise Server 11 Service Pack 1 for AMD64/EM64T SUSE LINUX Enterprise Server 11 for AMD64/EM64T SUSE LINUX Enterprise Server 10 Service Pack 4 for AMD64/EM64T SUSE LINUX Enterprise Server 10 Service Pack 3 for AMD64/EM64T PREREQUISITES: HP NC-Series QLogic (nx_nic) driver rpm version >= 4.0.540 Firmware version >= 3.4.336 for NC510C and NC510F Firmware version >= 4.0.230 for all other Products EFFECTIVE DATE: 03/20/2012 SUPERSEDES: CP015900.scexe DESCRIPTION: This scexe contains the utilities and binaries for upgrading Firmware on HP ProLiant QLogic NICs running the Linux x86_64 ENHANCEMENTS/FIXES: 1) This component now upgrades to fimware v4.0.582 2) Jumbo frames support for NC375T added The following steps must be performed in the specified order. Not following the specified order could result in the driver load not completing. A forced reboot will clear this condition. - Install a HP NC-Series QLogic (nx_nic) driver if not already installed. Install a version >= 4.0.540 and < 4.0.555 - Execute the scexe in interactive firmware upgrade mode and install the firmware: # ./CP016410.scexe - Reboot the server. - Install HP NC-Series QLogic (nx_nic) driver rpm version 4.0.555 or later. The driver must be uninstalled and reloaded. - Verify that the firmware version on the adapter is now latest. Table of Contents ================= Introduction Packaging Performing the Firmware Upgrade Firmware Upgrade Log Configure PXE/WOL/NCSI Important Information Introduction ============ This file describes the firmware upgrade of the HP Gigabit Server Adapters mentioned in the PRODUCTS AFFECTED section of this document. User guides and additional HP Network Adapter information can be found at: http://h18004.www1.hp.com/products/servers/networking/index-nic.html Packaging ========= The firmware upgrade utility is released in scexe format. The file is a single self-extracting executable that unpacks the component, runs it, and cleans up the component. This one-step process replaces the rpm format which would require three steps to install, execute, and remove. Performing the Firmware Upgrade =============================== 1. The utility requires nx_nic rpm installed and the module loaded. The module can be loaded by executing the below command. To install the rpm please refer the text file released with nx_nic rpm. # modprobe nx_nic 2. The firmware can be upgraded interactively using the following command: #./CP00xxxx.scexe 3. Check the help menu for more information regarding command line options. #./CP00xxxx.scexe -h Firmware Upgrade Log ==================== The results of the firmware upgrade are in the nxflash.log which will be written to the current working directory. Configure PXE/WOL/NCSI ============================== 1. The utility requires nx_nic rpm installed and the module loaded. The module can be loaded by executing the below command. To install the rpm please refer the text file released with nx_nic rpm. # modprobe nx_nic 2. Verify the configuration status of the network adapter by sending the following command: # ./CP00xxxx.scexe -c 3. Configure PXE/WOL/NCSI by sending the following command: # ./CP00xxxx.scexe [ interface ] pxe/wol/ncsi [ options ] options: 0 - Disable 1 - Enable example: The following command disables pxe # ./CP00xxxx.scexe eth0 pxe 0 Note: Please refer to the adapter QuickSpecs for information on supported features. Important Information ====================== 1) The nx_nic driver uses host-based firmware load. When the user loads the driver the host-based firmware image in the driver will be the version that is displayed when checking the firmware version using ethtool. The burned-in firmware on the device as well as the host-based firmware version can be verified by checking dmesg for entries similiar to the following: nx_nic: Flash Version: Firmware[4.0.516], BIOS[2.1.3] nx_nic: File FW[nx3fwmn.bin] version[4.0.516:12818] 2) On NC522m, NC522SFP etc that have only eeprom on the chip and thus share the fimware among all the ports, update is done only once. However other commands like show current ports and change the pxe setting etc treat the ports independently. This greately improves the performance of the tool. Thus please expect not to see all the ports that were displayed during -c invocation during the actual firmare update process. 3) This tool requires the supported interfaces to be active when executing because it queries the ethernet interface to get current version of firmware and driver. Hence, when a ethernet interface is not configured or is in a slave bonding configuration, this tool will not work as expected. Copyright 2011 Hewlett-Packard Development Company, L.P. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies