# changelog

author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14.1055
changelog:
  -      Firmware may skip rebuilding chunks of data on the new drive when the drive rebuild is performed followed by a Redfish Read On certain HPE servers with NS204i adapter card.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14.1063
changelog:
  -     Fix known issue on v1055 regarding RDE dictionary broken which will cause
      unexpected FW upgrading error.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.6-1.1
changelog:
  -      Improved the fan calibration during server power-on.
        * Improved the format of the Chassis CPLD version reported in Integrated Lights-Out 5 (iLO 5) and the Chassis Controller CLI.
        * Improved the fan behavior when a server blade stops communicating with the Chassis Controller.
        * Added support for Murata Power Supply Kits.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.9-1.1
changelog:
  -     Added Fan-FailSafe which continually checks to see if an installed, powered
      blade is communicating with the HPE Edgeline Chassis Controller. If there is
      no communication for 90 seconds or more, the fans will go to full blow. When
      the blade begins to communicate again, the fans will return to normal.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.04-7.1
changelog:
  -     .
      
      **The following fixes were incorporated in this version:**
      
        * The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
      
        * The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
      
        * Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
      
        * If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.
      
      Please refer to the _[Release
      Notes_](https://downloads.hpe.com/pub/softlib2/software1/pubsw-
      linux/p1400922138/v227320/20-D3000-Gen11RN504F_ED1.html) for the complete
      listing of fixes, enhancements, known issues and work-arounds corresponding to
      this firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.08.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.25
      
      14.0.499.25
      
      14.0.499.2
      
      14.0.490.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.03.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.0.499.29
      
      14.0.499.29
      
      14.0.499.2
      
      14.0.490.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.09.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.2.589.5
      
      14.2.589.5
      
      14.2.579.0
      
      14.2.566.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.2.589.5
      
      14.2.589.5
      
      14.2.579.0
      
      14.2.566.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.2.589.5
      
      14.2.589.5
      
      14.2.579.0
      
      14.2.566.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.2.589.5
      
      14.2.589.5
      
      14.2.579.0
      
      14.2.566.0
      
      Added support for:
      
      RedHat Enterprise Linux 8.8
      
      RedHat Enterprise Linux 9.2
      
      SuSE Linux Enterprise Server 15 SP5


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.10.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **Universal Boot Image**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.2.589.19
      
      14.2.589.19
      
      14.2.589.16
      
      14.2.566.0
      
      HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      14.2.589.19
      
      14.2.589.19
      
      14.2.589.16
      
      14.2.566.0
      
      HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.2.589.19
      
      14.2.589.19
      
      14.2.589.16
      
      14.2.566.0
      
      HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      14.2.589.19
      
      14.2.589.19
      
      14.2.589.16
      
      14.2.566.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2022.08.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.01
      
      09.09.00
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.01
      
      09.09.00
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.03.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.03
      
      09.09.20
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.04.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.04
      
      09.09.20
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.04.02
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.07.06
      
      09.09.20
      
      7.28
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.04.02
changelog:
  -     The Firmware fixes the following:
      
        * Unsuccessful read of the SFP Temperature which will trigger a Server Shutdown. 
        * Message related to a Mailbox 0x48 Firmware dump saved to buffer.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.09.01
changelog:
  -     Fixed the following behavior:
      
      Temperature Misreading: the adapter was reading incorrect reading of the
      temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small
      Form-factor Pluggable. The symptom would result in a temperature spike and
      potentially reset the system


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.09.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.08.05
      
      09.12.01
      
      7.34
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.08.05
      
      09.12.01
      
      7.34
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.08.05
      
      09.12.01
      
      7.34
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.08.05
      
      09.12.01
      
      7.34
      
      0.0
      
      Non-disruptive firmware upgrades: non-disruptive firmware updates is enabled
      and will not require a server reboot to apply.
      
      Added support for:
      
      RedHat Enterprise Linux 8.8
      
      RedHat Enterprise Linux 9.2
      
      SuSE Linux Enterprise Server 15 SP5


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2023.10.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.09.07
      
      09.14.01
      
      7.36
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.09.07
      
      09.14.01
      
      7.36
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.09.07
      
      09.14.01
      
      7.36
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.09.07
      
      09.14.01
      
      7.36
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2024.09.01
changelog:
  -     This Firmware package contains following firmware versions:
      
      **Adapter**
      
      **Speed**
      
      **MBI**
      
      **Firmware**
      
      **UEFI**
      
      **Boot Bios**
      
      HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.10.00
      
      09.15.00
      
      7.36
      
      0.0
      
      HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter
      
      32Gb
      
      02.10.00
      
      09.15.00
      
      7.36
      
      0.0
      
      HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.10.00
      
      09.15.00
      
      7.36
      
      0.0
      
      HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter
      
      64Gb
      
      02.10.00
      
      09.15.00
      
      7.36
      
      0.0


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.02.048.0
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial version of the firmware.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.005.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th Generation Intel Xeon Scalable Processors and 5th
      Generation Intel Xeon Scalable Processors. This version of the SPS should be
      paired with System ROM 2.16 (01/30/2024) or later.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may enter standby mode on Power-On Self-Test
      (POST) during warm reset cycle.
      
      Addressed an issue where system may stop responding at "Memory Initialization
      - Start" during Power-On Self-Test (POST).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.047.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th and 5th Generation Intel Xeon Scalable Processors.
      This version of the SPS should be paired with System ROM 2.20.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with Intel uPLR1 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.075.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th and 5th Generation Intel Xeon Scalable Processors. This
      version of the SPS should be paired with System ROM 2.40.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with Intel uPLR3 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.089.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th and 5th Generation Intel Xeon Scalable Processors.
      This version of the SPS should be paired with System ROM 2.50.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This version contains the latest Server Platform Services firmware for 4th and
      5th Generation Intel Xeon Scalable Processors.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.089.0-2.1
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Product Update (IPU) version IPU 2025.2 guidance.
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th and 5th Generation Intel Xeon Scalable Processors.
      This version of the SPS should be paired with System ROM 2.50.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This version contains the latest Server Platform Services firmware for 4th and
      5th Generation Intel Xeon Scalable Processors. This version is in compliance
      with IPU 2025.2 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Firmware contains fix for bug that may cause drive to perform self-initiated reset in systems where maximum queue depth of 128 is exceeded.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -      Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Assert fixes, logging enhancements and all current firmware improvements and bug fixes.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      This update includes a fix that prevents unrecoverable read errors in highly localized write intensive workload, and a new servo code revision that improves performance under specific vibration conditions.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      Update maximum continuous operation temperature values for host thermal management and reporting.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> GPK5-7.1
changelog:
  -      Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      Update maximum continuous operation temperature values for host thermal management and reporting.
        * Assert fixes, logging enhancements and all current firmware improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      Update maximum continuous operation temperature values for host thermal management and reporting.
        * Assert fixes, logging enhancements and all current firmware improvements.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      This firmware version updates the Vendor ID in the standard inquiry to 'HPE', in previous versions it was 'HP.'


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-3.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -      Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDA-3.1
changelog:
  -      Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2-7.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Fix command timeout and uncorrectable error improvement.
        * Added features for SAS4 auto power swtiching and thermal requirement.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      FW update to eliminate the risk of data error at unexpected power-off during specific I/O combination.
        * Adjust SoC clock in fw to bridge the LBA info. transfer timing gap and remove the risk of buffer CRC error.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-4.1
changelog:
  -      Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.
        * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.
        * Fix NVMe drive component which shows wrong behavior message against the flash result.
        * Fix SPP force upgrade flash component problem on certain drive family.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4IASHPK3
changelog:
  -      Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4IASHPK3-2.1
changelog:
  -      Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Reverted OCP spec features to maintain compliance to OCP spec commands over NVMe-MI
        * Implemented real Active Measured Latency by adding OCP 2.0 C3 Log page


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Improves data integrity
        * Decreases possibility of data corruption in certain error and timing conditions
        * Reduces the probability of hangs


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Improves performance in certain file systems and implements fixes for several of the previous firmware's shortcomings.
        * The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.
        * Several maintenance items are included in this firmware revision that reduce the probability of hangs.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     This firmware revision corrects a rare situation where a Cryptographic Erase
      could result in random data instead of the expected deterministic zeros. This
      is judged as low severity because it does not compromise user data or
      security, but justifies the update to preclude potential security concerns.
      There are several items that reduce the probability of hangs and provide some
      minor performance improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDA
changelog:
  -      This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
        * The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
        * Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDC
changelog:
  -      This maintenance revision improves data integrity.
        * The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-3.1
changelog:
  -      Online firmware flashing of drives attached to aSmart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiantand Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like(B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -     This FW release deploys an Enhanced Media Scan algorithm that addresses an
      issue when the host system does not provide enough idle time for drive's
      Foreground Media Scan to be activated, which is needed to ensure long term
      drive reliability. It also addresses few minor issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      The updates were included in a regularly scheduled 5300 maintenance release. This firmware has a security version upgrade to include TCGe SKUs and prevent a downloading of a back level firmware version of HPG0 after upgrading to HPG1.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -      Reduced the occurrence probability of PMIC busy issue. 
        * Fixed the system data error at the drive power on issue. 
        * When the PLP operation starts, the waiting Unmap request to the 4KB not-aligned host write area is canceled to be able to complete PLP correctly.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Fix for unrecovered errors which may occur on the targeted Blocks of Wear-leveling process when host issues Read command.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> MPK7625Q
changelog:
  -     Please refer to SID8624 wtih the reason that why upgrade requiremnet need to
      be set to Critical


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> MPK7625Q
changelog:
  -      Contains critical fix for issue where failure to send MI command completion could result in drive reporting 0GB until power cycled.
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00123725en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK5
changelog:
  -      Prioritize disabling Non-Fatal Error reporting at the beginning of FLR processing
        * Fix known FW bug PI/CI indexing issue


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK5
changelog:
  -      Prioritize disabling Non-Fatal Error reporting at the beginning of FLR processing.
        * Fix known FW bug PI/CI indexing issue.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK6
changelog:
  -      Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6.
        * For more information, CA is published at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-6.1
changelog:
  -      Corrects a potential data integrity issue during unaligned write commands, only found in supplier ongoing lab testing.Includes additional fixes to improve error handling and reliability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-2.1
changelog:
  -      Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     This firmware version updates the Vendor ID in the standard inquiry to 'HPE',
      in previous versions it was 'HP.'


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Removed printed circuit board assembly serial number from product serial number field on VPD 80h


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.
        * Adding other logging and FW enhancements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPDA-3.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configuratioans.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7
changelog:
  -      This firmware revision improves low-temperature performance and Error Correction Code (ECC) error recording for some commands. 
        * It also improves internal logging capabilities for failure analysis.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8
changelog:
  -      Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      The FW version is Changed from HPG0 to HPG1. Changed the thermal throttling scheme. SMART 60 was matched with Tcase 70 and Run the thermal throttling at SMART 65.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      HPG6 introduces bug fixes, reliability enhancement and modification in SMART Attributes. Once HPG6 is downloaded, the drive cannot be changed back to an earlier firmware (eg, HPG3).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7-2.1
changelog:
  -      Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.
        * Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.
        * Fix NVMe drive component which shows wrong behavior message against the flash result.
        * Fix SPP force upgrade flash component problem on certain drive family.
        * High Security Enablement support FIPs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Addresses a hot plug reporting concern
        * Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-7.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc...


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      This firmware provides a change to the Vendor ID in the VPD page that refers to HP instead of HPE.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Improves data integrity
        * Decreases possibility of data corruption in certain error and timing conditions
        * Reduces the probability of hangs and provide a minor performance improvement


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -      Improves data integrity. 
        * The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions. 
        * Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide a minor performance improvement.
        * Support firmware flash in OS FIPS enabled mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      This maintenance revision improves data integrity.  The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.
        * For more information, refer to HPE Customer Advisory at the following URL: [https://support.hpe.com/hpesc/public/docDisplay?docId=a00138902en_us](https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00138902en_us) which will be active on 24-April-2024.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.10
changelog:
  -      Support for AMD EPYC 9004 Series Processors.
        * Support for separate Power Domains for System and GPU based on Platform Support.
        * Incorporation of Secure Element controller on the system board for iLO to enable Transfer of Ownership. iLO6 firmware initializes and configures Secure Element with needed checks for secure transfer of ownership to OpenBMC in future.
        * IPMI changes for GPU temperature Threshold reporting.
        * iLO Redfish conformance Support - Location Indicator Active for Drive Objects.
        * iLO Redfish conformance Support - Power Subsystem and Thermal Schemas.
        * iLO Redfish conformance Support - Date Time local offset.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20
changelog:
  -      Support for Intel 4th Generation Xeon Processors.
        * Support for Intel Virtual RAID on CPU (Intel VROC).
        * Support for SPDM for increased Security with Storage and Network cards.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40
changelog:
  -      iLO enablement for new NVIDIA L40 PCIe acceletor
        * iLO enablement for new NVIDIA L4 PCIe accelerator
        * Need disk drive model stringetc for all drives in the server to be provided to COM
        * Hostname to be included in body of Redfish event
        * Enhance the update experience for PLDM Type-A components
        * Improvement on logging related to COM
        * Graceful shutdown support for COM initiated Firmware update
        * SMBIOS modification for High Bandwidth Memory (Intel Xeon CPU Max Series)
        * Supportability Improvement for DIAG Secure Element
        * Granular enable/disable of SNMP V1/V3 version
        * Pending reset flag support for COM initiated Firmware Update
        * Cloud based management enhancements for simplified onboarding
        * MCTP Device handling for FLR and BDF changes runtime for AMD
        * Display DA Drives when the VROC OOB driver is not available in ESXi
        * Enable/Disable IPMI KCS Interface through Redfish API


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40
changelog:
  -      Fixed IPMI SSIF MultiPart Command Failure issue (This enables IPMI utilities on ProLiant RL300 Gen 11 to use the SSIF interface for in-band management)
        * Fixed DIMM temperature reading data issue
        * Fixed The Firmware Update Operation Fail Through OneView for ME issue.
        * Fixed RDE VAS Reports Stack Memory Usage of 96%
        * Fixed the issue of Firmware flash fails during system reboots.
        * Fixed the issue of iLO Recovery from FTP not working
        * Fixed the issue of Hostname property & value missing in most of the REST events logged in Listener.
        * Fixed the issue of iLO UI/REST interfaces inaccessible when attempt to create event subscription during server POST complete.
        * Fixed the issue of Server state is Unmanaged in OV.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.41
changelog:
  -     iLO 6 v1.41 has the same content or feature set as iLO6 1.40 plus an
      additional fix for COM (Compute Ops Management) related to COM4VC bundle
      update message and event. The additional COM related fix is NOT applicable to
      other regular use case scenarios. Hence upgrading to iLO6 v1.41 is optional


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.41
changelog:
  -     Fix provided to have synchronous messages to reflect the status, to Compute
      Ops Management, after completion of server reset during bundle update in
      COM4VC use case scenario.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.45
changelog:
  -      Redfish APIs for iLO, System TPM measurement and SPDM capable option cards measurements. 
          * System TPM measurements are currently supported only on Intel and AMD platforms
          * Install TPM version 1.512 to use for System TPM measurements
        * Supported BIOS versions are Intel U54 v2.10 or later and AMD A55 v1.40 or later
        * Support for Universal Backplane Management Version 7
        * Added support for MCTP Device handling for FLR and BDF changes at runtime.
        * Added support to enable and disable IPMI KCS interface through iLO web interface and iLO Redfish API


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.45
changelog:
  -      Performance issue for Inband IPMI commands over SSIF interface (needs system ROM v1.40)
        * DL380 Gen11 binding vfio-pci driver to Intel E810 NIC causes iLO health monitoring failure
        * Schema Errors reported under /redfish/v1/ComponentIntegrity/
        * Incorrect Tasks status is shown when Redfish delete volume with Long Running Test
        * EDSFF NVMe SPDM Auth fails with iLO 6 1.40 Pass 6/7 Build with error as  (reason Unable to verify Signature)
        * Compute Ops Management for VCenter Reset task is added as BootUEFI(Graceful Shutdown) in the iLO Queue
        * BootToUefi(Graceful Shutdown) is added as Pending Reset task in the iLO Queue
        * During Bundle update one of the component f/w update fails
        * CPU Utilization graph is not updating when CPU is stressed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.50
changelog:
  -      Added capability in iLO for Two Factor Authentication using OTP (One Time Password) for Microsoft AD users
        * To display drive enclosure info in Firmware tab in iLO
        * Support for controller which goes for functional reset runtime
        * iLO to mark the correct component update status for runtime agent updatable components based on the update status and update result
        * Secure erase of data based on the usecase (customer, factory or openbmc ownership transfer)
        * iLO Support to Reduce AMD Bootup Delay. Reduce the delay by saving the memory trained data to specific location in BIOS SPI memory
        * iLO stops the bundle update in the scenario where BootToUefi task goes to exception to ensure Graceful shutdown of server
        * iLO Support for OBSE in factory mode without the need for Advance License
        * iLO will display Intel CFR Version in Process Information Page


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.50
changelog:
  -      OEM iLO component does not show the OEM equivalent entry for Intelligent Provision in One Time Boot Option
        * Handling delayed device discovered in UEFI mode during discovery phase
        * Persist the KCS interface setting across iLO reboots
        * Capability to enable KCS interface setting without needing a factory reset


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.51
changelog:
  -      Support for LocationIndicatorActive LED for NVMe drive when it is configured behind VROC controller
        * Support for StatusIndicator LED for NVMe drive when it is configured behind VROC controller
        * Support for telemetry streaming using Redfish event subscription


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.51
changelog:
  -      Incorrect reporting of the firmware version of Intel NVMe drives
        * Bundle update issue in case of file download failure for HPE GreenLake Compute Ops Management
        * iLO Two-Factor authentication login fails when AD user login name is used as username for iLO Login instead of AD user display name
        * Incorrect reporting of the Nic card port status from IPMI SDR list
        * Fixing HPE GreenLake Compute Ops Management retry logic to address HPE GreenLake Compute Ops Management status was changing from Connection in progress to Connection failed


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.52
changelog:
  -      iLO needs to provide IPv4 address for RDE enabled NIC
        * NVIDIA L40S needs to be enabled on HPE Servers (Gen11, Gen10 Plus)
        * iLO enablement for Intel Ponte Vecchio (PVC) for accelerator manageability and supportability
        * Reduce EDSFF power consumption using NVMe Power States feature
        * iLO enhancements to support SMBIOS 3.86 spec (type 197 and 242)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.52
changelog:
  -      Increased the maximum boot order to 512 as specified by UEFI EV specification
        * Incorrect sensor values for some sub-components in IPMI response
        * The "Ignore" option for the "Global Component Integrity" security parameter in the iLO Security Dashboard gets automatically disabled
        * The discrepancy between M.2 Slot Name with Redfish URI and iLO GUI is removed. The product name getting from backend will be displayed in redfish and UI as well
        * Enforced a limit of 14 bytes for DHCP v4 clientId. An error response of "400 - Bad Request" will be observed if the length is beyond 14 characters
        * Removal of duplicate sensor entries from IPMI response
        * UefiDevicePath length increased from 256 bytes to 1024 bytes


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.53
changelog:
  -      Fixed CloudConnect retry logic to reconnect to iLO once connectivity is resumed
        * Fixed the auto-connect issue if the HPE GreenLake Compute Ops Management (COM) was disabled due to a no-retry


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.53
changelog:
  -      Added support for Qualcomm X100
        * Added enhanced support to iLO firmware to report additional description about the components for HPE GreenLake Compute Ops Management initiated firmware bundle update
        * Added support to enable or disable User Accounts through Redfish and iLO web interface
        * In-band IPMI support for HPE ProLiant RL300 Gen11 servers (RHEL 8.6)
        * For PLDM components, added support to selectively update the target devices on the system through Install Sets and Task Queue


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.54
changelog:
  -      Gracefully handle multiple boot to UEFI commands in installset
        * Provide update statistics via Redfish for firmware bundle update
        * Redfish includes direct attach backplane in chassis collection
        * Redfish includes downstream backplane in chassis collection
        * Providing granular control on Security Parameters present on Security Dashboard
        * Intel VROC 8.2 support
        * Basic enablement of NVIDIA H100 94GB GPU


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.54
changelog:
  -      Fix has been implemented to show right data in redfish, which includes to suppress additional SetObject name when adapter provides expanded data for GET operation in RDE
        * Excessive event issue is fixed when RDE and DCi coexist on the system on iLO 5 and iLO 6
        * iLO Login page shows the Server as Managed by HPE OneView when actually the Server is in Monitored mode


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.55
changelog:
  -      Slowness due to continuously polling on timer expiry leading to increased CPU utilization
        * Added timestamp register call before iLO starts VSP logging to file to fix iLO VSP locks-up after an iLO reset if there is output displayed during the iLO reset
        * Firmware update fails through iLO web interface due to loss of network connectivity to iLO. You can now retry after 5 minutes when the network connectivity with iLO is restored
        * Existing subscriptions with HPE GreenLake for Compute Ops Management and HPE OneView is corrupt after upgrade to iLO 6 v1.54
        * PSU firmware upgrade flashing failure for Titanium PSUs


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.55
changelog:
  -      OpenSSL v1.0.2 in iLO FW is patched with Extended Master Secret support for TLS1.2
        * Updated the Eventing mechanism for State Transitions for Security Parameters for Security Dashboard
        * Boot time reduction on HPE ProLiant AMD based Gen11 systems by enabling support for BIOS eMCR feature
        * Redfish includes direct attach backplane in Fabric collection
        * Redfish schema amendments for DMTF compliance
        * Support for Prescott NDR200 IB/200G Ethernet dual-port QSFP112 adapter
        * Support for Intel Emerald Rapids and Sapphire Rapids EE LCC


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56
changelog:
  -      Addition of new SNMP trap (id# 6146) and Redfish event for runtime Mezzanine card failures on Synergy servers
        * Implemented Reconnect button in iLO UI for enabling customers to manually reconnect to HPE GreenLake for Compute Ops Management
        * In-band IPMI support for SLES 15 operating system on RL300 platforms
        * Configuration to allow disabling/enabling all weak ciphers and key lengths for SSH and TLS interfaces in Production security mode


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.57
changelog:
  -      iLO utilities, HPQLOCFG and HPLOMIG supports TLS 1.3 connections starting v6.1.0
        * OpenSSL upgraded from v1.0.2 to v3.0.12
        * Support for TLS1.3 has been added
        * Support for BlueField-3 DPU Model B3220 has been added
        * Storage Page enhanced to display storage enclosure, switch and port information in the topology


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.57
changelog:
  -      Fix for incorrect temperature sensor values and sensor indices reported by iLO SNMP interface
        * Fix for inconsistent physical drive status reported by iLO SNMP interface as compared with iLO GUI or Redfish interfaces
        * Support added for sending iLO AlertMail with TLS enabled, in conformance with RFC3207
        * Fix for configuring one time boot options via in-band and out-of-band IPMI methods
        * Fix for Web User interface being rendered inaccessible after the storage tab is clicked, in a server with large number of drives


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.58
changelog:
  -     For accessing drive temperature threshold data, the order will be MCTP over
      PCIe VDM as primary, MCTP over SMBUS as secondary and SMBUS 0x36 as last
      resort.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.59
changelog:
  -     1\. Support for Simplified Onboarding of HPE iLO to Compute Ops Management
      using an Activation Key.  
      2\. Support for consistent URIs (indexes) under Ethernet interfaces for
      systems in Gen 11 servers at all times.  
      3\. Ability to switch from DHCP6 to static IPv6 address for the same IP
      address.  
      4\. Pre-enablement of Qualcomm A100 Ultra Card limited to discovery and
      thermal monitoring.  
      5\. Added Cipher #17 for IPMI over LAN and removed Cipher #0 and Cipher #1
      with security issues.  
      6\. Ability for HPE iLO 6 to monitor Closed-Loop Liquid Cooling devices after
      the POST call completion.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.59
changelog:
  -     1\. Fixed an issue where the VSP used to get cleared upon an iLO reboot or an
      AUX server cycle.  
      2\. Fixed an issue where SMBIOS data file present in NAND is removed and
      recreated every time server reboots.  
      3\. Fixed an issue where the URI for TlsConfig was incorrect in the HPE iLO 6
      Redfish documentation.  
      4\. Fixed an issue where physical drive status was reported incorrectly in
      SNMP.  
      5\. Fixed an issue of invalid values for SNMP OIDs during SNMPWALK.  
      6\. Fixed an issue where while entering an incorrect HPE iLO password on a
      server in Edgeline EL8000t chassis displayed an improper error message.  
      7\. Fixed an issue where the IPMI power supply status showed a failure
      detected in empty bays on Apollo servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60
changelog:
  -     1. Support for Titanium PSU upgrade for 2200W PSUs.
        2. Support for Fan speed in terms of percentage from SNMP OID Get and Walk.
        3. Support for discovery and thermal monitoring of NVIDIA L20 accelerator card.
        4. Support for Active Directory Log in for group sizes larger than 300 and up to 800.
        5. Support for Floating Values in Redfish as per DMTF specification.
        6. Support for minimum15 concurrent sessions per user for each interface.
        7. Support for BlueField-3 DPU Model B3220.
        8. Support for HPE InfiniBand NDR/Ethernet 400Gb 1-port OSFP PCIe5 x16 MCX75310AAS-NEAT Adapter (P45641-B23/ P45641-H23).
        9. Support for HPE InfiniBand NDR200/Ethernet 200Gb 1-port OSFP PCIe5 x16 MCX75310AAS-HEAT Adapter (P45642-B22/ P45642-H22).
        10. Fixes for specific SNMP OIDs for RDE capable storage controllers for controller, physical drive, and logical drive properties.
        11. Enhancements to network stack to support the USGv6 requirements.
        12. Introduction of a Redfish property to enable or disable the RFC 7217 support in HPE iLO. By default, it is disabled. When enabled, this property changes the IPv6 SLAAC addresses of HPE iLO from EUI-64 format to the RFC format. For more information, see the HPE iLO Redfish documentation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60
changelog:
  -     1. Fixed an issue with the sensor index suffix in SNMP sensor name OIDs.
        2. Fixed an issue where, while updating the One Time Boot option to PXE boot device, the UEFI optimized boot mode was getting set to a disabled state.
        3. Fixed an issue where LDAP mode used to get disabled due to version and size mismatch.
        4. Fixed an issue where HTTP calls to Rest server (through a web server) to create installset, initiate installset, and read installset was unstable leading to failure in BundleUpdate.
        5. Fixed an issue where data from Redfish when appended with available data, use to generate unexpected data.
        6. Fixed an issue where ME was sending the wrong peci command code in response.
        7. Fixed an issue for Embedded ALOM and for other cards where the indexes were automatically assigned.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.61
changelog:
  -      Fixed the offline firmware update failure through SPP and missing the
      inventory of hard drives.
      
       Fixed the Uncorrectable Machine Check Exception (UMCE) and server start when
      HPE iLO reset is triggered.
      
       Fixed an issue where in a maximum configuration MR controller, the
      downstream UBM, and drives do not get listed in the device inventory or
      storage in HPE iLO.
      
       Fixed an issue where ME was sending the wrong peci command code in response.
      
       Fixed an issue with the sensor index suffix in SNMP sensor name OIDs.
      
       Fixed an issue where, while updating the One Time Boot option to PXE boot
      device, the UEFI optimized boot mode was getting set to a disabled state.
      
       Fixed an issue where LDAP mode used to get disabled due to version and size
      mismatch.
      
       Fixed an issue where HTTP calls to Rest server (through a web server) to
      create installset, initiate installset, and read installset was unstable
      leading to failure in BundleUpdate.
      
       Fixed an issue where data from Redfish when appended with available data,
      use to generate unexpected data.
      
       Fixed an issue for Embedded ALOM and for other cards where the indexes were
      automatically assigned.
      
       Fixed an issue where Edgeline servers could display an impossibly high
      chassis power reading, which was determined to be invalid.
      
       Fixed an issue where if a shared network port is not configured,
      SharedNetworkPortOptions property under URI
      /redfish/v1/Managers/1/EthernetInterfaces/2 was hidden. This will now be
      present and will display SharedNetworkPortOptions.NIC as Disabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.61
changelog:
  -      Support for Titanium PSU upgrade for 2200W PSUs.
      
       Support for Floating Values in Redfish as per DMTF specification.
      
       Support for Fan speed in terms of percentage from SNMP OID Get and Walk.
      
       Support for discovery and thermal monitoring of NVIDIA L20 accelerator card.
      
       Support for Active Directory Login for group sizes larger than 300 and up to
      800.
      
       Support for minimum 15 concurrent sessions per user for each interface.
      
       Support for BlueField-3 DPU Model B3220.
      
       Support for HPE InfiniBand NDR/Ethernet 400Gb 1-port OSFP PCIe5 x16
      MCX75310AAS-NEAT Adapter (P45641-B23/P45641-H23).
      
       Support for HPE InfiniBand NDR200/Ethernet 200Gb 1-port OSFP PCIe5 x16
      MCX75310AAS-HEAT Adapter (P45642-B22/P45642-H22).
      
       Fixes for specific SNMP OIDs for RDE capable storage controllers for
      controller, physical drive, and logical drive properties.
      
       Enhancements to network stack to support the USGv6 requirements.
      
       Introduction of a Redfish property to enable or disable the RFC 7217 support
      in HPE iLO. By default, it is disabled. When enabled, this property changes
      the IPv6 SLAAC addresses of HPE iLO from EUI-64 format to the RFC format. For
      more information, see the HPE iLO Redfish documentation.
      
       Added IML alert and Redfish Alert to report the following Intel Processor
      PROCHOT status:
      
       Warning alert or an event when an active PROCHOT is longer than 60 seconds.
      
       Repair alert or an event when there is a nonactive PROCHOT status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.61
changelog:
  -      Fixed the offline firmware update failure through SPP and missing the
      inventory of hard drives.
      
       Fixed a potential random server restart, or Uncorrectable Machine Check
      Exception (UMCE), when an iLO reset is triggered.
      
       Fixed an issue where in a maximum configuration MR controller, the
      downstream UBM, and drives do not get listed in the device inventory or
      storage in HPE iLO.
      
       Fixed an issue where ME was sending the wrong peci command code in response.
      
       Fixed an issue with the sensor index suffix in SNMP sensor name OIDs.
      
       Fixed an issue where, while updating the One Time Boot option to PXE boot
      device, the UEFI optimized boot mode was getting set to a disabled state.
      
       Fixed an issue where LDAP mode used to get disabled due to version and size
      mismatch.
      
       Fixed an issue where HTTP calls to Rest server (through a web server) to
      create installset, initiate installset, and read installset was unstable
      leading to failure in BundleUpdate.
      
       Fixed an issue where data from Redfish when appended with available data,
      use to generate unexpected data.
      
       Fixed an issue for Embedded ALOM and for other cards where the indexes were
      automatically assigned.
      
       Fixed an issue where Edgeline servers could display an impossibly high
      chassis power reading, which was determined to be invalid.
      
       Fixed an issue where if a shared network port is not configured,
      SharedNetworkPortOptions property under URI
      /redfish/v1/Managers/1/EthernetInterfaces/2 was hidden. This will now be
      present and will display SharedNetworkPortOptions.NIC as Disabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.62
changelog:
  -     iLO6 v1.62 Enhancements can be found at [www.hpe.com/support/ilo6-v1-62-Enhanc
      ements](http://www.hpe.com/support/ilo6-v1-62-Enhancements)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.62
changelog:
  -     iLO6 v1.62 Fixes information can be found at [www.hpe.com/support/ilo6-v1-62-F
      ixes](http://www.hpe.com/support/ilo6-v1-62-Fixes)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.63
changelog:
  -      Fixed an issue where fetching the email ID for AD login users fails in a cross-domain setup, affecting the ability to send TFA tokens.
        * Fixed an issue that involves a fallback mechanism to retrieve the email address from the parent domain if it cannot be fetched from the cross-domain.
        * Fixed an issue on gpio expander settings for Rinline 2 VRAN accelerator card.
        * Fixed an issue where the drives in the Embedded SATA controller were displayed in the label of Un-configured Drives instead of Drives.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.63
changelog:
  -      Added HPE iLO support for AMD Turin HPE ProLiant Gen11 platforms.
        * Added HPE iLO support for MCTP Bridge on AMD Turin HPE ProLiant Gen11 platforms.
        * Enabled out-of-band crash dump logging for AMD platforms.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.63
changelog:
  -      Fixed an issue where fetching the email ID for AD login users fails in a cross-domain setup, affecting the ability to send TFA tokens.
        * Fixed an issue that involves a fallback mechanism to retrieve the email address from the parent domain if it cannot be fetched from the cross-domain.
        * Fixed an issue on gpio expander settings for Nokia Cloud RAN SmartNIC Accelerator.
        * Fixed an issue where the drives in the Embedded SATA controller were displayed in the label of Un-configured Drives instead of Drives.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64
changelog:
  -      Support for PIN-based HPE iLO6 onboarding into COM instead of PCID.
        * Support for binding data center Secure Control Module (DC-SCM) and Host Processor Module (HPM) components through the HPE iLO UI on supported Modular Hardware Platforms.
        * Support for reporting boot progress states and boot time of a system through standard DMTF Redfish API.
        * Support for version reporting in GUI through the Rest API for Side Band Board CPLD, Switch Board CPLD, Power Distribution Board CPLD, Riser MCU FW and OCP interposer CPLD for HPE ProLiant Compute Gen 12 DL320, and HPE ProLiant Compute Gen 12 DL340 SP servers.
        * Added a threshold to the power for NVMe drives so that the server can meet the acoustic and operating temperature target.
        * Added support to Add to Queue pane to move the task to the start of the installation queue.
        * Added support to display the total estimated fan power consumption of all the fans in the server in the power meter graphs.
        * Support for LLDP (link layer discovery protocol) over a Dedicated Network that is used by network devices for advertising their identity, capabilities, and neighbors on a LAN based on IEEE technology. However, this is not applicable for HPE Synergy servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64
changelog:
  -      Fixed an issue where HPE iLO RIBCL queries generated incorrect CAPACITY VALUE responses.
        * Fixed an issue where fetching the email details of LDAP user where DistinguishedName containing special characters were causing the two-factor authentication process to fail.
        * Fixed the cpqHoMIBStatusArray status issue that did not get updated with proper details when a drive attached to HPE Smart Array P408i-a SR controller failed or degraded.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.66
changelog:
  -      Ability of HPE iLO to report standard RAS errors for processor, memory, and PCI for HPE Compute ProLiant DL384 Gen12 servers.
        * Ability of the HPE iLO interface to set and obtain the thermal configuration setting called Smooth Cooling along with the other existing configurations.
        * Enabled the Compute Utilization Per Second (CUPS) metrics for Intel Sierra Forest processors. This includes CPU, memory, and I/O utilization and CPU power per socket and CPU average frequency per socket.
        * Added an option using REST API to rotate the ESKM password.
        * Added IML, Redfish and SNMP alerts to report cases of invalid Power Distribution Board (PDB) on ProLiant DL320 Gen12 platform
        * Added support for digit validation in PIN based onboarding of iLO to COM


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.66
changelog:
  -      Fixed an issue where param2 check-in challenge_auth response for NVIDIA adapter failed during SPDM authentication.
        * Fixed an issue where the Kerberos client advertised insecure encryption (RC4, DES) types and rejected the deprecated ones. As a part of this fix, RC4, DES, and 3DES algorithms are removed from the Kerberos requests.
        * Fixed an issue where the MCTP retry mechanism in i2c communication failed. 
        * Fixed an issue where a low value of the HPE iLO reset progress bar time caused mismatch in the configuration during the HPE iLO reset time.
        * Fixed an issue where the IPMI fan's pwm values were set to a default of 255 to calculate dutycycle percentage.
        * Fixed an issue with the time delay between retries for PCIe VDM transmit buffer.
        * Fixed an issue for the sensor values that were reported in the GET_SENSOR response though these sensors were marked as non-supported in the PDR table.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.67
changelog:
  -      Renamed the front OCPA and OCPB labeling in REST and HPE iLO UI to OCP Slot
      A and OCP Slot B.
      
       Renamed the rear OCPA and OCPB labeling in REST and HPE iLO UI to OCP Slot A
      and OCP Slot B.
      
       Ability of HPE iLO Redfish to raise a clear event notification for an air
      filter replacement.
      
       Support for Azure Stack HCI 23H2 OS.
      
       Adhered to HPE branding guidelines.
      
       Addition of HPE ProLiant Advanced License to HPE iLO with HPE Compute Ops
      Management.
      
       Support for the Virtual Media Mount URL length increased to 1023 characters.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.67
changelog:
  -      Fixed an issue where there was no VSP output on DL360 Gen11 HPE iLO6 due to
      stack overflow on VSP log buffer handling.  
       Fixed an issue where the memory health status on HPE ProLiant Compute DL384
      platforms appeared to be degraded.  
       Fixed an issue where the fan speed was not set as per the thermal
      configuration due to server device discovery not reaching
      vMainDeviceDiscoveryComplete.  
       Fixed an issue that did not allow to enable mTLS for subscription and
      returned error in loading client private key.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 226.1.107.0
changelog:
  -      This product addressed device lost symptom after continuously ungraceful restart on BCM57414 OCP3 adapter.
        * This product addressed some RDE pattern format for some LLDP properties.
        * This product addressed the NC-SI passthrough with BMC when device is under idle mode.
        * This product addressed new mechanism for loading factory default.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.28.60
changelog:
  -     This product now supports the following network adapters:
      
        * Broadcom BCM5719 Ethernet 1Gb 4-port Base-T Adapter for HPE
        * Broadcom BCM5719 Ethernet 1Gb 4-port Base-T OCP3 Adapter for HPE


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.31.0
changelog:
  -     This product addresses an issue the adjustment of firmware read-write commands
      on corresponding OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.32.3
changelog:
  -     This product correct an issue which the Boot Code Version of the Firmware did
      not get updated after upgrading the Firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33.3
changelog:
  -      This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
        * This product adds to support HPE MicroServer Gen11


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33.3
changelog:
  -      This product fixes the intermittent issue of displaying incorrect device status under iLO web
        * This product fixes the intermittent lost iLO connection with shared networking mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.1
changelog:
  -      This product addressed a problem where Reboot Required option was not set after doing firmware update under RBSU.
        * This product addressed the disconnection with iLO after switching to Shared Network mode on BCM5719 OCP3 adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.50
changelog:
  -     This product addresses an issue where the FAN behavior with installed BCM 5719
      1Gb 4p BASE-T OCP Adptr.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.70
changelog:
  -     This product addresses an issue where Loses IP Address Randomly during AC/DC
      cycle and idling.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.70
changelog:
  -     This product addresses an issue where network loses IP Address Randomly during
      AC/DC cycle and idling.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.35.3
changelog:
  -      This product addressed abnormal fan behavior when BCM5719 OCP3 installed.
        * This product addressed the failure of IP dispatch when using BCM5719 LOM as shared iLO networking.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.35.3
changelog:
  -      This product addressed abnormal fan behavior when BCM5719 OCP3 installed.
        * This product addressed the failure of IP dispatch when using BCM5719 LOM as shared iLO networking.
        * This product addressed that platform might encounter a POST failure when NX1-based controllers and some storage controllers combines.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.37.0
changelog:
  -      This product fixed error checking sequence for Firmware Management Protocol API.
        * This product fixed NC-SI commands to interoperate more benefit with iLO.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.38.0
changelog:
  -      This product addresses a problem that might cause a BSOD when trying to reboot the system from operating Windows systems due to NIC internal software mutex problem.
        * This product addresses an issue where a random missing DHCP IP address occurs when the iLO shared NIC port is used, due to NIC internal software mutex problem.
        * This product addresses an issue that might cause the POST to get stuck due to NIC internal software mutex problem.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.39.0
changelog:
  -      This product fixes an issue where a dummy Serial Number is seen immediately after update the adapter firmware to version 2.30 (or earlier).
        * This product fixes an issue where Wake-on-LAN not working is seen.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.1
changelog:
  -     *Changes and New Features in version 1.8.1.0.0 :**
      
        * Added hfi1_eprom **v10_8_0_0_13.**
        * Loader ROM **HfiPcieGen3Loader_1.8.1.0.0.rom** and driver EFI **HfiPcieGen3_1.8.1.0.0.efi** were added.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.0
changelog:
  -     *Fixes included in version 1.11.0:**
      
        * **The following issue has been fixed in Unified Extensible Firmware Interafce (UEFI) ROM: **On some platforms, the hfi1 device was not showing up in BIOS/UEFI boot menus and was not available as a PXE boot device. This was caused by the platform not loading the UEFI driver for the hfi1 adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12.0-2.1
changelog:
  -     *Fixes included in version 1.12.0:**
      
        * Fixed race condition between BIOS checking link status and LNI completing which resulted in PXE boot failures.
        * Changed the default behavior of the hfi1_eprom tool to convert the eprom format to version 2, eliminating the need to supply the -N command line argument.
        * Addressed an issue where updating the HfiPcieGen3Loader*.rom file could result in the erasure of HfiPcieGen3Loader*.efi and HFI_TYPE1*.dat files.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20.11
changelog:
  -      This product now supports SUSE Linux Enterprise Server 12 SP5.
        * This product now supports HPE ProLiant MicroServer Gen10 Plus and HPE ProLiant XL225n Gen10 Plus.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.21.5
changelog:
  -     This product now supports the following network adapters:
      
        * Intel X710-DA2 Ethernet 10Gb 2-port SFP+ OCP3 Adapter for HPE
        * Intel X710-DA2 Ethernet 10Gb 2-port SFP+ Adapter for HPE


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.11
changelog:
  -      This product now supports SUSE Linux Enterprise Server 15 SP2.
        * This product now supports Red Hat Enterprise Linux 8, Update 2 and Update 3.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.55
changelog:
  -     This product addresses an link issue for Intel X710-DA2 Ethernet 10Gb 2-port
      SFP+ OCP3 Adapter for HPE.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.5
changelog:
  -     This product now supports Red Hat Enterprise Linux 8 update 4 and SUSE Linux
      Enterprise Server 15 Service Pack 3


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.50
changelog:
  -      This product addresses an issue where the incorrect translation is seen with Intel Intel I350-T4 Ethernet 1Gb 4-port BASE-T  Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.25.4
changelog:
  -     This product addresses an issue where the adaters isn't recongized with HPE
      Ethernet 10Gb 2-port SFP+ OCP3 X710-DA2  Adapter and HPE Ethernet 10Gb 2-port
      SFP+ X710-DA2 Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30.0
changelog:
  -      This product now supports Red Hat Enterprise Linux 9 Update 3.
        * For more product details, please refer to the latest document in https://www.intel.com/content/www/us/en/download/19622/


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.2(C) contains updates to the firmware packaging and is functionally
      equivalent to ver. 1.0.2. It is not necessary to upgrade with Revision C if a
      previous component revision was used to upgrade the firmware to version 1.0.2.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial verison of the firmware.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.4(C) contains updates to the firmware packaging and is functionally
      equivalent to ver. 1.0.4. It is not necessary to upgrade with Revision C if a
      previous component revision was used to upgrade the firmware to version 1.0.4.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Modified the ADC conversion formula based on the new layout design of Gen11
      AMD platforms.  
      Improved the accuracy of Fast Platform Triggering mechanism on AMD platforms.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.21-1.1
changelog:
  -      A controller lockup issue occurs when clearing the configuration of an encryption-enabled controller.
        * When unconfigured drives are directly attached, the PHY ID is always 0 in the ADU report or lsscsi output.
        * A file system or application might read incorrect data when there is pending read or write operation and an array transformation is in progress on the logical drives.
        * A rekey operation on a SmartCache volume pauses when the controller firmware is upgraded and the server is warm rebooted.
        * A SMART READ DATA command sent with an out-of-band method returns a response of all zeros.
        * The Maximum Connection Number calculation for an indirectly attached wide-port end-target is incorrect.
        * A firmware exception might occur during task management abort handling for a non-NCQ SATA command.
        * A controller lockup issue might occur when the PHYs fluctuate between link up/link down status.
        * Open frames cause an I/O timeout that results in an Open Reject Bad Destination response and a host I/O timeout. This situation causes a server node to be evicted from a cluster.
        * Removing a redundant fan module in an attached JBOD causes Failed JBOD status.
        * The controller might not respond for up to 15 minutes when a drive reports a hardware failure.
        * Specifying an incorrect serial number in the API when attempting to HALON flash a drive does not result in the expected error.
        * A SmartCache write bypass might result in a cache line getting stuck on a pending queue if the write to the primary logical drive is retried.
        * A controller might not respond if it is repeatedly forced between SIS (Inbox) and PQI I/O submission modes at the same time as an I/O timeout.
        * An issue in the write coalescing logic might cause a partially coalesced opportunity to be abandoned under high queue depth workloads.
        * The OS driver reports a lockup code that does not match the code provided by the firmware.
        * SATA drives are unnecessarily reset during a power-on self-test.
        * The bay number of a non-hot-plug drive is reported as 255/0xFF when the device inventory re-query API is initiated.
        * A controller might not respond when a clear configuration action is initiated at the same time that a degraded volume is undergoing Rapid Parity Initialization.
        * I/O coalescing is not enabled when DDR cache is not present or enabled.
        * A drive incorrectly reports failed status if it is spun down and then used to create a volume with Rapid Parity Initialization.
        * SmartCache metadata is lost after a new volume is created while running I/O traffic.
        * An abnormal volume state is observed with multiple SmartCache volumes configured using 512e drives.
        * A controller might not respond during volume transformation if the backup power source goes off line, is spuriously hot-removed, or indicates a cabling error.
        * A LUN reset issue occurs during heavy write I/O workloads on cache enabled volumes.
        * An incorrect spare SSD physical drive state is reported during a rebuild.
        * An I/O latency issue occurs during periodic disk write metadata operations.
        * A drive failure code might be incorrectly updated with a generic drive failure code.
        * When an expanding SmartCache volume is migrated to another controller after an ungraceful shutdown, the volume is not configured correctly.
        * A controller might not respond when an expanding volume is migrated from a controller that supports DDR cache to a controller that does not support DDR cache.
        * In a split mirror configuration, the cache ratio is reset to the default values after a backup cable error.
        * A controller might not respond after a cold boot during volume rekeying.
        * A controller lockup issue might occur in an HBA SAS drive dual path configuration.
        * A device reset command initiated by a host utility has a timeout issue in minimum power mode.
        * If you use the identify all LED command frequently, the command might not affect all drive LEDs.
        * A controller might not respond when you run the Internal Test Unit Ready command during drive hot removal or addition.
        * A controller lock up issue might occur when resuming a rebuild operation after a reboot.
        * A surface scan inconsistency check event is not logged for RAID 1 volumes.
        * A controller lock up issue might occur when activating a spare drive for an encrypted volume during I/Os.
        * A drive that failed due to read capacity is presented to the host.
        * A periodic background drive temperature check might skip every other minute.
        * A controller lock up issue might occur during expansion after multiple subsequent attempts to abort the expansion process.
        * An unknown error occurred during execution when Recover Cache Module in SSA.
        * Encryption host management commands are processed for a SmartCache volume, even though these commands do not apply to SmartCache volumes.
        * A host might read incorrect data after an array expansion operation.
        * High severity events logged when a controller is in the critical event buffer overflow condition are not prioritized.
        * Redundant surface scan pass complete events might be posted for the same surface scan iteration if the controller is rebooted during the scan.
        * During an expander firmware upgrade (reduced functionality mode), the last management device index remains open for processing I/Os, and an I/O timeout might occur.
        * A performance drop is observed on certain queue depths for the 4 kB sequential write workload on RAID logical volumes with SmartPath and DDR caching disabled.
        * A command timeout issue occurs during expander firmware upgrade with Non-Disruptive Soft Reset.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.53
changelog:
  -      Added UBM type3 backplane support
        * Added support for long device model/product ID for SATA drives.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 3.53
changelog:
  -      An issue where the controller might become unresponsive while waiting for a non-existent pre-fetch queue entry.
        * Host I/O timeouts might occur due to continuing firmware attempts to discover devices during an expander configuration.
        * A controller lockup problem (with code 0x1E10) might occur when a bad drive with an unsupported block size is connected into slot 0.
        * A Controller hangs issue when multiple hot-plug and hot remove events (drives or JBODs) were being processed.
        * A Controller hangs issue on DDR caching enabled logical volumes with sequential read towards the end of the volume.
        * A Controller hangs issue with outstanding I/Os on a degraded logical volume when the physical drive fails.
        * A Controller hangs issue if a host I/O and background consistency check simultaneously encounter a RAID-1 ADM stripe in which all drives have URE's on the same LBA.
        * A Controller hangs issue when a drive is failed from a RAID6/60 logical drive when the host issues a Clear Controller Configuration command or any other configuration change command.
        * The SSD data drive might be set offline (with reason code 0x37) when hot-remove and re-insert during a spare rebuild in progress.
        * A drive might not be exposed to the OS after reboot if the system is rebooted just after the sanitize erase finishes.
        * UBM backplanes are not detected properly when connected to specific ports (port 7 or above) in an expander card configuration.
        * A Controller hangs issue when processing idle time followed by a short burst of I/Os.
        * The controller might return the previous drive firmware version, after a drive firmware update on SATA drives.
        * The controller might fail drives (with reason code 0x49, I/O freeze timeout) during expander firmware upgrade on a multi-expander enclosure configuration.
        * Hot-added drive LED control fails on specific fan-out expander type external enclosure models.
        * sequential I/Os and the firmware coalescing logic can't get the memory.
        * Filesystem or application might read old data when SmartCache configurations encounter intermittent write I/O errors to a primary logical drive.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4.11
changelog:
  -      Fixed an issue where SSD SmartPath is not enabled on logical drives created on the same array in certain scenarios.
        * Fixed a problem where WRITE and READ fails with URE on a RAID6 volume where it could have completed successfully in certain error recovery scenarios.
        * Fixed a problem where events were not getting logged in certain scenarios.
        * Fixed an issue where a Windows memory dump process was taking longer than 30 minutes.
        * Fixed a problem in Gen10+ server where FAULT LED was not turning on for the drives failing during device discovery.
        * Fixed a problem where the critical event "Controller memory ECC error limit exceeded" was reported in the AHS IML log after upgrading to 3.53 B0 firmware build.
        * Fixed a problem where the host WRITE I/O failed on the SmartCache logical drive with UREs present on the primary logical drive.
        * Fixed an issue where the controller may be non-responsive after drive failure with SSD SmartPath enabled under a high queue depth workload.
        * Fixed a performance issue when the host is submitting large sequential IO streams at high queue depth.
        * Fixed an issue where OS filesystem is not available after making configuration changes in HII.
        * Fixed an issue where error was observed while selecting edit SmartCache Logical drive option when SmartCache logical drive is in Degraded mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.00
changelog:
  -      Added support for DMTF PLDM Monitoring and Control for enhanced thermal monitoring
        * Added support for DMTF PLDM Redfish Device Enablement for Redfish Storage, StorageController, Port, Drive, Volume, & CollectionCapabilities
        * Added support for DMTF PLDM Redfish Device Enablement for Volume POST & DEL operations
        * Added support for DMTF Redfish StorageDevice.1.0.1 Events
        * Added support in firmware to enable logical drive transformation without backup power source on the controllers supporting data preservation.
        * Added support to return NCQ Priority Information for SATA drive to host.
        * Added support to blink the drive Predictive Failure (PF) LED during Predictive Spare Rebuilding (PSR) for drives that can be safely removed and replaced without causing a logical drive failure.
        * Added support to configure default setting for the drive write cache.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.00
changelog:
  -      Fixed a rare problem where backup power status was incorrectly reporting Charging instead of Failed.
        * Fixed an issue where obsoleted SCSI pass through command fails.
        * Loss of redundant path message is incorrectly reported on logical drive failure with single domain configuration.
        * Fixed an issue where SmartPath may not be used after LUN Reset
        * Fixed a potential controller lockup 0x1BC0 during write then read I/O with drive URE's.
        * Fixed an issue that Apollo 4200 Gen10 plus LFF expander backplanes are not discovered by controller.
        * Fixed an issue that range locked SED failed with reason error erasing RAID metadata during reboot and remains failed after clear configuration.
        * Fixed an issue where the file system may read incorrect data from a degraded RAID 5 or 6 logical drive.
        * Fixed an issue where the file system or application may read incorrect data when a backup power source is discharged completely, and system power loss occurs during a transformation.
        * Fixed an issue where the drive Fault LED is not turned ON when firmware fails a bad HBA drive connected to an expander during device discovery or hot-plug.
        * Fixed an issue of auto-rebuild not starting if two drives fail at the same time on a RAID10 or RAID6 logical drive having only one "Auto-Replace Drives" spare drive.
        * Fixed an issue where the drive Fault LED is turned ON for a few seconds when multiple configured drives are hot removed from a SES enclosure and then hot added
        * Fixed an issue where rebuild did not start after multiple iterations of drive failures.
        * Fixed an issue where the controller might fail to discover devices after a cable is hot-added.
        * Fixed a potential problem of inability to delete a SmartCache write-back logical drive.
        * Fixed an issue where 0x1789 POST message error code is displayed as healthy and there is no information in HII when all logical drives in the controller are offline.
        * Fixed an issue where the last logical drive in an array cannot be deleted in UEFI configuration tool.
        * Fixed an issue where build method is not listed for RAID 6 array creation in UEFI configuration tool.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.61
changelog:
  -      Added support for for Local Key Management SED adapter password.
        * Added support for reporting surface scan metrics for SSA, SSACLI.
        * Added support for improving secure erase time for disks supporting the WRITE SAME command.
        * Added support for a new persistent event log policy that overwrites old events with the most recently occurred events.
        * Added support PLDM firmware update
        * Added support PLDM firmware update for UBM.
        * Enable Redfish Name property of Volume resource which is optional on create. The value is the same as DisplayName property.
        * Report VendorID, ProductID and location informations for enclosure SEPs.
        * Redfish POST request to perform the Drive.Actions.#SecureErase ACTION will be rejected with the extended error message ResourceInUse if the targeted Drive is a SED that is not in the original factory state(OFS).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 5.61
changelog:
  -      Fixed an issue where to create RAID 60 on 24 SATA SSDs resulted in controller lockup.
        * Fixed a performance drop issue on RAID 5 logical drives with 50/50 cache ratio on a 256K sequential read workload.
        * Fixed a parity inconsistency after RAID rebuild restarted with a new drive replacement.
        * Fixed an issue where a transforming logical drive fails when the controller is abruptly rebooted after logical drive deletion.
        * Fixed an issue where the logical drive failed during the heal array transformation.
        * Fixed an issue where rebuild does not start on an array with the spare disk.
        * Fixed an issue where the VDM requests were not being serviced in a timely manner when the controller was under high load.
        * Fixed controller lockup during clear configuration after SmartCache logical drive is moved from P-Series to E-Series controller.
        * Fixed an issue where not all permitted values were published to the WriteCachePolicy@Redfish.AllowableValues in VolumeCapabilities.
        * Fixed an issue where the VolumeCapabilities resource can be published with incorrect values for WriteCachePolicy@Redfish.AllowableValues when the controller's battery is charging.
        * Fixed an issue where the ControllerPasswordAccepted Redfish alert was sent with incorrect ControllerPasswordEntered messageId.
        * Fixed an issue where a drive's ServiceLabel is sometimes erroneously published with a leading zero on its Port number.
        * Fixed an issue where Redfish alerts generated early in the boot sequence were not reported to iLO.
        * Fixed an issue where a Redfish Volume create request is erroneously accepted when the request payload contains a WriteCachePolicy value conflicting with the existing cache configuration.
        * Fixed an issue where the ControllerPreviousError alert was sent with incorrect ControllerPreviouseFailure messageId and severity.
        * Fixed an issue where the BatteryCharging alert was sent with an incorrect severity on certain controllers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.2-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.2.2(C) contains updates to the firmware packaging and is functionally
      equivalent to ver. 1.2.2. It is not necessary to upgrade with Revision C if a
      previous component revision was used to upgrade the firmware to version 1.2.2.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial verison of the firmware.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12_11-24-2022
changelog:
  -     This revision of the System ROM improves the system boot time when Restoring
      Default Manufacturing Settings.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12_11-24-2022
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the latest revision of the AMD
      reference code for AMD 4th Generation EPYC processors which addresses an issue
      of potential over voltage condition early in the boot sequence. This issue is
      not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20_01-06-2023
changelog:
  -     See the release document A55_1.20_01_06_2023 in Download Product Binaries page
      from Product Summary of the firmware product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22_01-19-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may hang at POST during TPM measurement after
      restoring manufacturing defaults.
      
      Address an issue where the RegistryVersion format in the URI
      redfish/v1/registrystore/registries did not follow the Redfish Specification.
      If scripts were written to conform with the incorrect format in previous
      System ROMs, those scripts may need to be modified to follow the correct,
      Redfish compliant format which is implemented in this System ROM revision and
      later.
      
      Addressed an issue where the System Configuration (RBSU) option "Access
      Control Service" did not disable PCIe Access Control Service when it's set to
      disabled.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20_01-06-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 4th Generation EPYC processors.
      
      Addressed an issue where SMBIOS Type17 memory width showed non-zero for an
      empty DIMM slot.
      
      Addressed an issue where system would RSOD if DesiredBootDevice was set but
      not matched with any boot option.
      
      Addressed an issue where the POST progress bar was shown in the wrong
      position.
      
      Addressed an issue where AGESA PI version did not show in SMBIOS type40.
      
      Corrected Ext Maximum Memory value in SMBIOS entry.
      
      Removed Boot Mode Option from BIOS/Platform Configuration (RBSU) Menu.
      
      Removed unsupported Enhanced Processor Performance Profile from BIOS/Platform
      Configuration (RBSU) Menu.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22_01-19-2023
changelog:
  -     Add new System Configuration (RBSU) configuration options that allow
      controlling the processor's P0 (maximum) frequency. This includes the "Custom
      Pstate0" option with settings of "Auto" (default) and "Manual" and the
      "Pstate0 Frequency(MHz)" option that allows setting the P0 frequency. When the
      "Custom Pstate0" option is configured for "Manual", the value of the "Pstate0
      Frequency(MHz)" is used for the processor's P0 frequency. When the "Custom
      Pstate0" option is configured for "Auto", the processor uses its normal,
      maximum P0 frequency and the "Pstate0 Frequency(MHz)" option is not
      configurable. In System Configuration (RBSU), these options are located under
      the BIOS/Processor Options. This setting has the following Redfish properties:
      /redfish/v1/systems/1/bios/settings/CustomPstate0
      /redfish/v1/systems/1/bios/settings/Pstate0Frequency
      
      Remove the System Configuration (RBSU) option for "Memory Interleaving Mode".
      This option is no longer configurable because AMD recommends always enabling
      this capability for maximum performance. Memory Interleaving will always be
      enabled with this revision or later of the System ROM no matter how this
      option had been previously configured. In System Configuration (RBSU), this
      option had previously been located under the Memory Options. This setting had
      the following Redfish properties:
      /redfish/v1/systems/1/bios/settings/AmdMemoryInterleaving


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30_03-06-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 4thGeneration EPYC processors.
      
      This revision of the System ROM updates zlib to 1.2.13 which provides
      mitigation for BIOS security vulnerability documented as CVE-2022-37434
      (https://nvd.nist.gov/vuln/detail/CVE-2022-37434). This security vulnerability
      is documented in the CVE report site.
      
      This revision of the System ROM includes the v1.1.1s openSSL which provides
      mitigation for BIOS security vulnerability documented as CVE-2022-2097
      (https://nvd.nist.gov/vuln/detail/CVE-2022-2097). This security vulnerability
      is documented in the CVE report site.
      
      Addressed an issue where some Chinese translation is missing from RBSU.
      
      Addressed an issue where some Japanese translation is missing from RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.32_05-29-2023
changelog:
  -     Reduced system boot time.
      
      Improved the description of Unsupported DIMM Configuration in the Integrated
      Management Log (IML) and POST error message.
      
      Added support for AMD 4th Generation EPYC 9754/9734 Processors.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.32_05-29-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.7
      for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.7
      for AMD 4th Generation EPYC processors.
      
      Addressed an issue where SMBIOS Type 199 did not have Microcode patch
      information.
      
      Addressed an issue where the xGMI link speed information was not shown on the
      POST screen.
      
      Addressed an issue where NVME drives would require a re-scan after hot-
      add/remove on Windows 2019.
      
      Addressed an issue where the Windows ipmiutil tool may encounter an
      unspecified error.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_07-12-2023
changelog:
  -     Removed "NUMA memory domains per socket" selection item "Auto" from RBSU,
      because value of Auto option is actually set to one memory domain per socket.
      Set display default to "One memory domain per socket".
      
      Added "NVMe PCIe Resource Padding" option under "Advanced PCIe Configuration"
      in RBSU. The option is for fixing a failure to hot add NVMe drive to empty
      slot under OSes such as VMware. The option can be set from Redfish URI
      "/redfish/v1/systems/1/bios/settings/" with property "PciResourcePadding".


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_07-12-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.8
      RC3 for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for and security vulnerabilities
      documented as CVE-2023-2650.
      
      Addressed an issue where the unsupported DIMM population IML will report an
      incorrect processor number on dual-processor systems.
      
      Addressed an issue where the SMBIOS type 197 might contain an incorrect format
      value of xGMI speed.
      
      Addressed an issue where the CXL root bridge was missing from SMBIOS type 9.
      
      Addressed an issue where dmidecode indicates 4 power supplies are installed
      when only 2 power supplies are actually installed.
      
      Addressed an issue where number of "Internal L3 cache" displayed under RBSU
      information page is not correct.
      
      Addressed an issue where the System Health LED is illuminated Red for all
      memory configuration error cases.  Some memory configuration error cases are
      not critical and should have the System Health LED illuminated Amber.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.42_08-16-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Address an issue that can result in a Red Screen of Death (RSOD) and hang
      during system boot or a hang during system boot without an RSOD. This issue
      can occur on systems utilizing the v1.32 or v1.40 System ROM revision and iLO
      Firmware revision v1.50. The v1.32 System ROM added a boot-time reduction
      capability (which also required iLO Firmware revision v1.50) which resulted in
      the boot-time RSOD and/or hang. This capability has been removed in this
      revision of the System ROM.
      
      Addressed an issue where one-time boot did not work properly after setting
      one-time boot device from iLO web or via Redfish.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.50_10-04-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.9
      for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system might be repeatedly rebooting due to PCI bus
      reallocation feature.
      
      Addressed an issue where secure boot key would not be set to default when
      perform manufacturing default from iLO web.
      
      Addressed an issue where EDSFF form factor would be displayed as "unknown" in
      SMBIOS type 242.
      
      Addressed an issue where system might hang since BIOS might fail to access iLO
      resource.
      
      Addressed an issue where system might hang when accessing devices attached on
      the switch board (SWB).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.54_11-02-2023
changelog:
  -     Added new Microsoft secure boot keys, KEK2023, Microsoft UEFI CA 2023 and
      Windows UEFI CA 2023, since the original keys will expire in 2026.
      
      When the RBSU knob "Trusted Platform Module Options\Advanced Trusted Platform
      Module Options\TPM Visibility" was changed from "Hidden" to "Visible", RBSU
      knobs "TPM 2.0 Endorsement Hierachy" and "TPM 2.0 Storage Hierachy" would be
      set to "Enabled" automatically. Therefore, the BitLocker Recovery Console
      prompt would not appear when booting to Windows after changing TPM back to
      visible if Bitlocker was already enabled on OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.54_11-02-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.A
      for AMD 4th Generation EPYC processors. This revision of the System ROM
      updates OpenSSL to 1.1.1v which provides mitigation for BIOS security
      vulnerability documented as CVE-2023-3817.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where iLO device did not present in Windows system
      management devices, and results in iLO related service failure when embedded
      video is disabled from RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56_12-08-2023
changelog:
  -     Added a system boot-time reduction System Configuration (RBSU) option "System
      Options/Boot Time Optimizations/AMD eMCR Boot-Time Reduction" and set to
      "Enabled" by default. This function required iLO firmware revision 1.55 to
      take effect. This setting has the following Redfish properties:
      
      /redfish/v1/systems/1/bios/settings/AmdEmcr


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.56_12-08-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Greyed out the System Configuration (RBSU) option "System Options/Boot Time
      Optimizations/Extended Memory Test" since it is not supported on HPE
      DL325/345/365/385 Gen11 servers.
      
      Greyed out the System Configuration (RBSU) option "Memory Options/Memory
      PStates" since it is not supported on HPE DL325/345/365/385 Gen11 servers.
      
      Addressed an issue where SMBIOS type 9 Designation showed an incorrect string
      when an OCP retimer card was installed.
      
      Addressed an issue that can result in a system hang while loading defaults
      when a user default was saved before.
      
      Addressed an issue where system memory training failed with certain DIMMs.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.58_01-04-2024
changelog:
  -     Added the System Configuration (RBSU) option "Boot Options/UEFI Boot
      Settings/Filter Non-bootable Drives" and set to "Auto" by default. This
      setting has the following Redfish property:
      
      /redfish/v1/systems/1/bios/settings/FilterNonbootableDrive


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.58_01-04-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.B
      for AMD 4th Generation EPYC processors. This revision provides AMD's
      mitigation for security vulnerabilities for CVE-2023-31346 and CVE-2023-31347
      for AMD 4th Generation EPYC processors. This security vulnerability is
      documented in the CVE report site. This issue is not unique to HPE servers.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Greyed out the System Configuration (RBSU) options "PCIe Device
      Configuration/Advanced PCIe Configuration/PCIe Bifurcation Options/PCIe Slot
      21/22 Bifurcation" since it is not supported on HPE DL325/345/365/385 Gen11
      servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.58_01-04-2024-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.58_01-04-2024(B) contains updates to the firmware packaging and is
      functionally equivalent to ver. 1.58_01-04-2024. It is not necessary to
      upgrade with Revision B if a previous component revision was used to upgrade
      the firmware to version 1.58_01-04-2024.
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.B
      for AMD 4th Generation EPYC processors. This revision provides AMD's
      mitigation for security vulnerabilities for CVE-2023-31346 and CVE-2023-31347
      for AMD 4th Generation EPYC processors. This security vulnerability is
      documented in the CVE report site. This issue is not unique to HPE servers.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Greyed out the System Configuration (RBSU) options "PCIe Device
      Configuration/Advanced PCIe Configuration/PCIe Bifurcation Options/PCIe Slot
      21/22 Bifurcation" since it is not supported on HPE DL325/345/365/385 Gen11
      servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_03-21-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2023-45853, CVE-2022-36763 and CVE-2022-36764. This revision
      of the System ROM includes the mitigation for vulnerabilities documented as
      CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where System Configuration System Configuration (RBSU) knob
      "PCI Device Config\PCIe Data Link Feature\Slot 21/22 PCIe Data Link Feature
      Exchange" cannot be disabled.
      
      Addressed an issue where System Configuration (RBSU) knob "Power and
      Performance Options\AMD Core Performance Boost" cannot be disabled.
      
      Corrected the PCIe slot number for NS204i-u.
      
      Corrected SATA port numbers in System Configuration (RBSU).
      
      Corrected SATA HDD location in One-Time Boot Menu.
      
      Addressed an issue where the boot order of NVMe drives cannot be changed.
      
      Addressed an issue where the OS could not detect the iSCSI drive through IPv6
      installation when iSCSI IpAddressType is set to auto,
      
      Addressed an issue where system boot slowly with Intel E810 NIC.
      
      Added help string for System Configuration (RBSU) knob "Power and Performance
      Options\Advanced Power Options\Infinity Fabric Performance State"
      
      Addressed an issue where the PCR7 value might be changed randomly on every
      boot.
      
      Addressed an issue where Redfish resource was not updated after deleting
      secure boot keys via System Configuration (RBSU).
      
      Addressed an issue where the system failed to enroll certificate to PK and KEK
      via Redfish.
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2023-45853, CVE-2022-36763 and CVE-2022-36764.
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.62_05-22-2024
changelog:
  -     Displayed "Last Power Down Reason" in POST messages.
      
      Removed unsupported System Configuration (RBSU) option "Memory Options/AMD
      Periodic Directory Rinse".
      
      Added the System Configuration (RBSU) option "Processor Options/AMD Periodic
      Directory Rinse Tuning" and set to "Auto" by default. This setting has the
      following Redfish property:
      
      /redfish/v1/systems/1/bios/settings/AmdPeriodicDirectoryRinseTuning


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.62_05-22-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.C
      for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may hang while enrolling secure boot key dbr
      certificate via Redfish API.
      
      Addressed an issue where system failed to boot with selected NVMe HDD by
      setting One-Time Boot Option in ILO Web.
      
      Addressed an issue where TPM PCR0 value might change after changing some
      System Configuration (RBSU) options
      
      Addressed an issue where the boot order was cleared unexpectedly after
      configuring System Configuration (RBSU) options and navigating to Boot Options
      > UEFI Boot Settings > UEFI Boot Order then pressing F12 to Save and Exit.
      
      Removed the value "Not Specified" in System Configuration (RBSU) option
      "Server Security/Trusted Platform Module Optioins/Current TPM 2.0 Active PCRs"
      and set the default value as "SHA1 and SHA256"
      
      **Known Issues:**
      
      System may encounter boot failure or become unstable after downgrading system
      ROM to 1.60 or older versions. It is not recommended to downgrade system ROM
      to an older version or apply default system settings after downgrading if
      needed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.64_06-19-2024
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where TPM PCR0 value might be changed if PCIE riser
      configuration is changed.
      
      Addressed an issue where PCIE Link speed may remain in Gen1 if F12 - Save and
      Exit was not pressed after configuring max PCIE speed to per port control.
      
      Addressed an issue where system may encounter a RSOD while updating SAS drive
      FW via HPE Service Packs, including, but not limited to, VMware ESXi Online
      HDD FW Component Bundle 16.00, HPE Synergy Service Pack (SSP) 2024.01.02
      (January 2024) and the future HPE Synergy Service Pack (SSP) 2024.07.01 (July
      2024).
      
      Addressed an issue where some settings in RBSU may not restore to default
      after applying "Restore Default Manufacturing Settings".
      
      Addressed an issue where the RBSU/Firmware update shows "Flash successfully"
      message when incorrect SATA firmware was loaded for upgrade.
      
      Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword
      were not working.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.66_07-11-2024
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may encounter performance degradation and TSC
      unstable issues.
      
      Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword
      may not work.
      
      Addressed an issue where NVMe hot plug of certain ports did not work in VMWare
      8.0.
      
      Addressed an issue where duplicated and incorrect task status were logged in
      iLO Event Log when enrolling duplicated keys via Redfish API.
      
      Addressed an issue where multiple KEK instances appeared after the enrollment
      of KEK certificate via Redfish API.
      
      Addressed an issue where dbr were not deleted after deleting all keys via
      Redfish API
      
      Addressed an issue where TPM PCR0 may change after modifying some RBSU knobs.
      
      Addressed an issue where Negotiated Link Width in RBSU shows incorrect
      information after configurating bifurcation.
      
      Addressed an issue where system may encounter RSOD after enrollment of an
      improper certfifcate.
      
      Addressed an issue where the Logical Drive name was cleared in RBSU after
      leaving configuration page of MR controller.
      
      Addressed an issue that Battery Failure IML message may be incorrectly logged
      for MR Controller with Smart Storage Battery.
      
      Addressed a secure boot database synchronizing issue when manging secure boot
      keys via Redfish API.
      
      Addressed an issue where TPM PCR0 may change after swapping ROM in iLO web.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.68_08-09-2024
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      This is the first ROM version which supports iLO6 1.6.2. Downgrading to an
      older ROM version is not supported after upgrading to iLO6 1.6.2.
      
      **Problems Fixed:**
      
      Addressed an issue where system may hang while resetting the system.
      
      Addressed an issue where NS204i may not be identified as an NVMe device.
      
      Addressed an issue where NVMe hot plug function may fail in VMWare when the
      GPU riser was installed.
      
      Addressed an issue where duplicated and incorrect task status was logged iLO
      Event Log.
      
      Addressed an issue where multiple KEK instances were displayed after
      enrollment of KEK certificate from Redfish API.
      
      Addressed an issue where dbr was not deleted after deleting all keys via
      Redfish API.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.70_09-05-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.D
      for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where System Information\Device Inventory in ILO web may
      show unknown entries after enabling bifurcation.
      
      Addressed an issue where One button secure erase (OBSE) report may show
      incorrectDrive Port Number and Box Number for MicroChip SR controller.
      
      Addressed an issue where system may become stuck after enrolling many
      certificates and signatures.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_11-08-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.2
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.D for AMD 4th Generation EPYC
      processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the "Server Boot Order" in iLO web was not aligned
      with "UEFI Boot Order Control" in RBSU.
      
      Addressed an issue where CPU may not set cTDP to maximum by default.
      
      Addressed an issue where an error message in Linux would indicate TCG log size
      is not compatible.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.14_10-11-2024
changelog:
  -     *Important Notes:**
      
      Initial version to support AMD 5th Generation EPYC processors. This revision
      of the System ROM includes AMD reference code GenoaPI 1.0.0.0 for AMD 5th
      Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This is the initial version to support AMD 5th Generation EPYC processors.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_11-08-2024
changelog:
  -     Improved system power consumption in idle state.
      
      Added the System Configuration (RBSU) option "PCIe Device
      Configuration/Advanced PCIe Configuration/PCIe Hot-Plug Error Control" and set
      to "Hot-Plug Surprise" by default. This setting has the following Redfish
      property:
      
      /redfish/v1/systems/1/bios/settings/PcieHotPlugErrControl


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30_01-17-2025
changelog:
  -     Added new Microsoft Option Rom UEFI CA 2023 secure boot key.
      
      Added the "Smooth Cooling" selection to the Thermal Configuration option in
      the RBSU\Advanced Options\Fan and Thermal Options. This selection modifies the
      fan speed response to improve acoustics by reducing the rate of fan speed
      changes. This can improve acoustics for workloads which significantly vary CPU
      utilization. Note that this option can result in a small reduction in
      performance due to the short durations of CPU thermal throttling and some
      operating systems, such as Linux, may log CPU thermal throttling events. These
      events do not indicate an issue with the system and can be ignored.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30_01-17-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC
      processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Consistent Device Naming (CDN) may not work when
      it is enabled.
      
      Addressed an issue where the SMBIOS TYPE 4 max speed may be incorrect.
      
      Addressed an issue where the system would use UUID for IPV6 DHCP when
      "RBSU\Network Options\Network Boot Options\IPv6 DHCP Unique Identifier\DUID-
      LLT" is selected.
      
      Addressed an issue where the system iLO remote console might hang when the
      System Utilities Language is set to Japanese.
      
      Addressed an issue where the system might bring up a warning message ("ERST:
      [Firmware Warn]: too many record IDs!") in the Linux environment during boot
      up.
      
      Addressed an issue where some strings of "NVMe-oF Configuration and Attempt
      pages" in system RBSU menu are still in English after switching the language
      to a non-English one.
      
      Addressed an issue where the system RBSU menu might list duplicate or
      incorrect network interfaces in the selection page.
      
      Addressed an issue where the system RBSU menu might not display clear drive
      location information.
      
      Addressed an issue where the system may report dmesg error messages (NULL
      net_device) in the Linux environment, or the system may encounter a NIC option
      (MR216) not responding situation.
      
      **Known Issues:**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.32_02-21-2025
changelog:
  -     Added pop-up message for all Intelligent Provisioning boot paths to warn users
      of the risk of data loss.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.32_02-21-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC
      processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system may encounter an SMI storm when PCIe error
      disconnect recover (EDR) failed.
      
      Addressed an issue where the system may fail to update NVMe drive firmware.
      
      Addressed an issue where NVMe-oF may not be detected during VMWare
      installation.
      
      Addressed an issue where the system may reboot continuously when PCIE resource
      need to reallocate.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34_03-11-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.3
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC
      processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when performing firmware update
      via Firmware Management Protocol.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.40_03-21-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.4
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC
      processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system may encounter RSOD and fail to update
      firmware while performing firmware update.
      
      Addressed an issue where the system may encounter RSOD if NVMe-oF target did
      not have partitions.
      
      Addressed an issue where System Power Supply information in SMBIOS type39 is
      incorrect when there are more than 2 PSUs.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.42_04-09-2025
changelog:
  -     Added help text for "Smooth Cooling" RBSU option.
      
      Added the System Configuration (RBSU) option "PCIe Device
      Configuration/Advanced PCIe Configuration/PCIe Hot-Plug Error Control" and set
      to "Hot-Plug Surprise" by default. This setting has the following Redfish
      property:
      
      /redfish/v1/systems/1/bios/settings/PcieHotPlugErrControl


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.42_04-09-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.4
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.E for AMD 4th Generation EPYC
      processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where some GPUs may encounter a PCIe lane drop when an
      NS204i-u is installed.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50_05-16-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code TurinPI 1.0.0.5
      for AMD 5th Generation EPYC processors. This revision of the System ROM
      includes AMD reference code GenoaPI 1.0.0.F for AMD 4th Generation EPYC
      processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Name field of the Logical Drive under MR
      controller page might be missing or changed unintentionally after exiting and
      going back to the MR controller page.
      
      Addressed an issue where the messages of "HPE Intelligent Provisioning" is
      incorrect for OEM customers.
      
      Addressed an issue where some options are missing for RBSU knob "Enabled Cores
      per Processor".
      
      Addressed an issue where SMT was not enabled if Enabled Cores per Processor is
      set to less than 8 cores.
      
      Addressed an issue where certain GPU may encounter lane drop issue with
      NS204i-u installed.
      
      Addressed an issue where OCP device cannot be disabled by RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20_01-06-2023
changelog:
  -     See the release document A56_1.20_01_06_2023 in Download Product Binaries page
      from Product Summary of the firmware product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20_01-06-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes an updated revision of the AMD
      reference code for AMD 4th Generation EPYC processors.
      
      Addressed an issue where SMBIOS Type17 memory width showed non-zero for empty
      DIMM slot.
      
      Addressed an issue where system would RSOD if DesiredBootDevice was set but
      not matched with any boot option.
      
      Addressed an issue where POST progress bar was shown in the wrong position.
      
      Addressed an issue where AGESA PI version did not show in SMBIOS type40.
      
      Corrected Ext Maximum Memory value in SMBIOS entry.
      
      Removed Boot Mode Option from BIOS/Platform Configuration (RBSU) Menu.
      
      Removed unsupported Enhanced Processor Performance Profile from BIOS/Platform
      Configuration (RBSU) Menu.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_07-12-2023
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.8
      for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the revision of the OpenSSL library
      1.1.1u update which provides mitigation for and security vulnerabilities
      documented as CVE-2023-2650.
      
      Addressed an issue where the unsupported DIMM population IML will report an
      incorrect processor number on dual-processor systems.
      
      Addressed an issue where the SMBIOS type 197 might contain an incorrect format
      value of xGMI speed.
      
      Addressed an issue where the CXL root bridge was missing from SMBIOS type 9.
      
      Addressed an issue where dmidecode indicates 4 power supplies are installed
      when only 2 power supplies are actually installed.
      
      Addressed an issue where number of "Internal L3 cache" displayed under RBSU
      information page is not correct.
      
      Addressed an issue where the System Health LED is illuminated Red for all
      memory configuration error cases. Some memory configuration error cases are
      not critical and should have the System Health LED illuminated Amber.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30_10-04-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.D
      for AMD 4th Generation EPYC processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where System Information\Device Inventory in iLO web may
      show unknown entries after enabling bifurcation.
      
      Addressed an issue where One button secure erase (OBSE) report may show
      incorrect Drive Port Number and Box Number for MicroChip SR controllers.
      
      Addressed an issue where system may become stuck after enrolling many
      certificates and signatures.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_01-17-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E
      for AMD 4th Generation EPYC processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system would use UUID for IPV6 DHCP when
      "RBSU\Network Options\Network Boot Options\IPv6 DHCP Unique Identifier\DUID-
      LLT" is selected.
      
      Addressed an issue where the system iLO remote console might hang when the
      System Utilities Language is set to Japanese.
      
      Addressed an issue where the system might bring up a warning message ("ERST:
      [Firmware Warn]: too many record IDs!") in the Linux environment during boot
      up.
      
      Addressed an issue where some strings of "NVMe-oF Configuration and Attempt
      pages" in system RBSU menu are still in English after switching the language
      to a non-English one.
      
      Addressed an issue where system RBSU menu might list duplicate or incorrect
      network interfaces in the selection page.
      
      Addressed an issue where the system RBSU menu might not display clear drive
      location information.
      
      Addressed an issue where the "Server Boot Order" in iLO web is not aligned
      with "UEFI Boot Order Control" in RBSU.
      
      Addressed an issue where an error message in Linux would indicate TCG log size
      is not compatible.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.50_02-21-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E
      for AMD 4th Generation EPYC processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system may encounter an SMI storm when PCIe error
      disconnect recover (EDR) failed.
      
      Addressed an issue where the system may fail to update NVMe drive firmware.
      
      Addressed an issue where NVMe-oF may not be detected during VMWare
      installation.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.52_03-11-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.E
      for AMD 4th Generation EPYC processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when performing firmware update
      via Firmware Management Protocol.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_04-21-2025
changelog:
  -     Added help text for "Smooth Cooling" in system configuration (RBSU) option.
      
      Added the System Configuration (RBSU) option "PCIe Device
      Configuration/Advanced PCIe Configuration/PCIe Hot-Plug Error Control" and set
      to "Hot-Plug Surprise" by default. This setting has the following Redfish
      property:
      
      /redfish/v1/systems/1/bios/settings/PcieHotPlugErrControl


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_04-21-2025
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.F
      for AMD 4th Generation EPYC processors.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Name field of the Logical Drive under MR
      controller page might be missing or changed unintentionally after exiting and
      going back to the MR controller page.
      
      Addressed an issue where the messages of "HPE Intelligent Provisioning" is
      incorrect for OEM customers.
      
      Addressed an issue where the system may encounter RSOD and fail to update
      firmware while performing firmware update.
      
      Addressed an issue where the system may encounter RSOD if NVMe-oF target did
      not have partitions.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.00_04-02-2025
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Removed dynamic power capping support for this release. It is not supported
      for now.
      
      Enabled Spread Spectrum.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.42_05-10-2025
changelog:
  -     *Important Notes:**
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Swaped PCIe Slot 7 and Slot 8 identifiers.
      
      Fixed SMBIOS to support 12 power supplies.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_05-27-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Product
      Update (IPU) version IPU.2024.1 guidance. This version of the System ROM
      contains updates aligned with the 5th Generation Eagle Stream Intel Xeon
      Processor Scalable Family maintenance release 1 (MR1). This revision of the
      System ROM includes the mitigation for security vulnerabilities CVE-2023-5678,
      CVE-2024-0727 and CVE-2023-45229. The security vulnerabilities are documented
      in the CVE report site. They are not unique to HPE servers. This version of
      the System ROM should be paired with Server Platform Services (SPS) Firmware
      06.01.04.047.0 (2.20_03_26_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may hang while enrolling secure boot key dbr
      certificate via Redfish API.
      
      Addressed an issue where system failed to boot with selected NVMe HDD by
      setting One-Time Boot Option in ILO Web.
      
      Addressed an issue where the boot order was cleared unexpectedly after
      configuring System Configuration (RBSU) options, navigating to Boot Options >
      UEFI Boot Settings > UEFI Boot Order and then pressing F12 to Save and Exit.
      
      Removed value "Not Specified" in System Configuration (RBSU) option "Server
      Security/Trusted Platform Module Optioins/Current TPM 2.0 Active PCRs" and set
      the default value as "SHA1 and SHA256".
      
      Addressed an issue where Redfish resource was not updated after deleting
      secure boot keys via System Configuration (RBSU).
      
      Addressed an issue where the system failed to enroll certificate to PK and KEK
      via Redfish.
      
      Addressed an issue where the OS could not detect the iSCSI drive through IPv6
      installation when iSCSI IpAddressType is set to auto.
      
      Addressed an issue where the boot order of NVMe drives cannot be changed.
      
      Addressed an issue where system may encounter a RSOD while updating SAS drive
      FW via HPE Service Packs, including, but not limited to, VMware ESXi Online
      HDD FW Component Bundle 16.00, HPE Synergy Service Pack (SSP) 2024.01.02
      (January 2024) and the future HPE Synergy Service Pack (SSP) 2024.07.01 (July
      2024).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.22_06-19-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.047.0 (2.20_03_26_2024). This version of the System
      ROM contains updates aligned with the Intel uPLR1 OOB2 guidance.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where a NVMe drive would not be unmounted when it exceeds
      the DPC error threshold with ESXi 8.0U2 or newer versions.
      
      Addressed an issue where system would not be configured as 4 sub-NUMA nodes
      per socket (SNC4) when Virtual NUMA is enabled and SNC2 is enabled.
      
      Addressed an issue where updating NVMe-oF initiator name would not take
      effect.
      
      Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword
      were not working.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30_08-09-2024
changelog:
  -     Updated some Japanese translation
      
      Added support for 12 DIMM per CPU population mixed rank.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30_08-09-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel uPLR2
      guidance. This version of the System ROM should be paired with Server Platform
      Services (SPS) Firmware 06.01.04.047.0 (2.20_03_26_2024).
      
      **Firmware Dependencies:**
      
      This is the first ROM version which supports iLO6 1.6.2. Downgrading to an
      older ROM version is not supported after upgrading to iLO6 1.6.2.
      
      **Problems Fixed:**
      
      Addressed an issue where duplicated and incorrect task status were logged iLO
      Event Log.
      
      Addressed an issue where multiple KEK instances appeared after the enrollment
      of KEK certificate from Redfish API.
      
      Addressed an issue where UEFI secure boot dbr signatures were not deleted
      after deleting all keys via Redfish API.
      
      Addressed an issue where Negotiated Link Width in RBSU showed incorrect
      information after configuring bifurcation.
      
      Addressed an issue where system may encounter RSOD after enrollment of an
      improper certificate.
      
      Addressed an issue where the Logical Drive name was cleared in RBSU after
      leaving the configuration page of MR controllers.
      
      Addressed an issue where Redfish BIOS actions, ResetBios and ChangePassword
      may not work.
      
      Addressed a secure boot database synchronizing issue via Redfish API.
      
      Addressed an issue where an error message is displayed with 12-DIMM per CPU
      and DIMM rank mixing for unsupported DIMM configurations.
      
      Addressed an issue that Battery Failure IML message log may be incorrectly
      logged for Smart Array Controller with Smart Storage Battery.
      
      Addressed an issue where NS204i may not be identified as an NVMe device.
      
      Addressed an issue when setting "Workload Profile" to 'Custom' and changing
      "Processor Monitor/Mwait Support" to 'Disabled'. "Processor Monitor/Mwait
      Support" knob is not seen in the BIOS->Service Options.
      
      Addressed an issue where the driver Health Message was shown twice in POST
      when drive was removed and ran cold boot.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.32_09-09-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel uPLR2
      OOB2 guidance. This version of the System ROM should be paired with Server
      Platform Services (SPS) Firmware 06.01.04.047.0 (2.20_03_26_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where System Information\Device Inventory in iLO web may
      show unknown entries after enabling bifurcation.
      
      Addressed an issue where System Information\Device Inventory in iLO web may
      miss devices after enabling bifurcation.
      
      Addressed an issue where One button secure erase (OBSE) report may show
      incorrect Drive Port Number and Box Number for MicroChip SR controller.
      
      Addressed an issue where system may become stuck after enrolling many
      certificates and signatures.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34_10-04-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.047.0 (2.20_03_26_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the firmware version and status in device inventory
      show incorrectly after setting bifurcation for option cards.
      
      Addressed an issue where the product name information in Device Inventory of
      iLO web may show unknown or blank for M.2 drives.
      
      Addressed an issue where ilorest BIOS attributes PersistentMemScanMem,
      PersistentMemAddressRangeScrub and PersistentMemNumaAffinity may present
      randomly.
      
      Fixed an issue where the iLO firmware version may show incorrectly.
      
      Fixed an issue where system may not have an evenly distributed NUMA node
      assignments among PCI slots for virtual NUMA mode.
      
      **Known Issues:**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.40_11-08-2024
changelog:
  -     Added new IML messages to indicate the status of NVMe secure erase and AMT.
      
      Added the System Configuration (RBSU) option "Power and Performance Options/
      Advanced Performance Options/HardwarePM Interrupt" and set to "Disabled" by
      default. This setting has the following Redfish property:
      
      /redfish/v1/systems/1/bios/settings/HwpmInterrup


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.40_11-08-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel EGS BKC
      UPLR3 release. This version of the System ROM should be paired with Server
      Platform Services (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the "Server Boot Order" in iLO web was not aligned
      with "UEFI Boot Order Control" in RBSU.
      
      Addressed an issue where the system might be asserted when plugging in
      MR416i-p.
      
      Addressed an issue where an error message in Linux would indicate TCG log size
      is not compatible.
      
      Addressed an issue where incorrect drive location information would be shown.
      
      Addressed an issue where RSOD might occur after enable PCH VMD with 2x M.2
      NVMe drives.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.42_12-06-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might detect memory uncorrectable error
      while system has been idle for extended period of time.
      
      Addressed an issue where the system might hang at memory initialization after
      restoring system setting to factory default.
      
      Addressed an issue where system RBSU menu might list duplicate or incorrect
      network interfaces in the selection page.
      
      Addressed an issue where some strings of in the System
      Configuration\RBSU\Network Options\NVMe-oF Configuration\NVMe-oF Attempt are
      still in English after switching the language to non-English version.
      
      Addressed an issue where the NVMe image description in RBSU might be incorrect
      when VROC is enabled.
      
      Addressed an issue where the system RBSU menu might not display clear drive
      location information.
      
      Addressed an issue where fans might rapidly ramp up and then back down.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.42_12-06-2024
changelog:
  -     Added new Microsoft Option ROM UEFI CA 2023 secure boot key.
      
      Updated the boot device string rules to include the case when VMD is enabled.
      
      Added "Smooth Cooling option" in the "RBSU\Advanced Options\Fan and Thermal
      Options".


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.44_01-17-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system would use UUID for IPV6 DHCP when DUID-LLT
      is selected.
      
      Addressed an issue where the system would report Unsupported DIMM
      Configuration when having 16+0 DIMM mixed rank population.
      
      Addressed an issue where the system Consistent Device Naming (CDN) is not
      working in Windows Server.
      
      Addressed an issue where the system memory address translation did not match
      with system limitation.
      
      Addressed an issue where the system iLO remote console might hang when the
      System Utilities Language is set to Japanese.
      
      Addressed an issue where the system might bring up a warning message ("ERST:
      [Firmware Warn]: too many record IDs!") in the Linux environment during boot
      up.
      
      Addressed an issue where the system Max/Min Uncore Frequency value did not be
      set to default value after loading default settings.
      
      **Known Issues:**
      
      None.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.46_02-21-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when both TXT and TDX are
      enabled.
      
      Addressed an issue where the system might fail to update NVMe drive firmware.
      
      Addressed an issue where the system might not be able to detect disk removal
      via NVMe-oF during VMware installation.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.48_03-11-2025
changelog:
  -     *Important Notes:**
      
      None
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when performing firmware update
      via FMP.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.48_03-11-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when performing firmware update
      via Firmware Management Protocol.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50_04-22-2025
changelog:
  -     Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS
      Settings for FlexRAN v2.0.
      
      Added help text for "Smooth Cooling" in system configuration (RBSU) option.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50_04-22-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Name field of the Logical Drive under MR
      controller page might be missing or changed unintentionally after exiting and
      going back to the MR controller page.
      
      Addressed an issue where the messages of "HPE Intelligent Provisioning" is
      incorrect for OEM customers.
      
      Addressed an issue where the Intel PCH model name might be unknown in system
      configuration (RBSU) -> System information.
      
      Addressed an issue where the system might fail to detect EDSFF SED drives with
      Intel VROC.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50_04-22-2025-2.1
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel IPU
      2025.2 updates.
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.089.0 (2.50_04_01_2025).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Name field of the Logical Drive under MR
      controller page might be missing or changed unintentionally after exiting and
      going back to the MR controller page.
      
      Addressed an issue where the messages of "HPE Intelligent Provisioning" is
      incorrect for OEM customers.
      
      Addressed an issue where the Intel PCH model name might be unknown in system
      configuration (RBSU) -> System information.
      
      Addressed an issue where the system might fail to detect EDSFF SED drives with
      Intel VROC.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.24_03-03-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Added capability to support 4th Gen Intel Xeon Scalable Processors MCC.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30_03-01-2023
changelog:
  -     Added capability to support 4th Gen Intel Xeon Scalable Processors 4S.
      
      Enhanced PCI information in Active Health System log.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30_03-01-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Always Power On function would remain off when
      factory defaults are loaded.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.32_03-23-2023
changelog:
  -     Enhanced error reporting function for Intel Xeon Max Series.
      
      Enhanced Power and Performance Options in ROM-Based Setup Utility.
      
      Added a new feature to support customized iPXE image.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.32_03-23-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue where EDSFF drive was not detected intermittently when system
      started.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_06-29-2023
changelog:
  -     Added support for Agentless Attestation. This security capability allows
      detecting potentially malicious changes to the system by obtaining system
      measurements (which include firmware revisions, configuration settings, and
      the hardware configuration) via the Redfish API.
      
      Added segment value in PCI addresses under RBSU PCI device information.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_06-29-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where a drive cannot be unmounted after hot-plug
      interruption during DPC (Downstream Port Containment) recovery process under
      VMware.
      
      Addressed an issue where Citrix HyperVisor could not be installed.
      
      Addressed an issue where the system would hang in POST if Intel UPI link
      enablement was set to single link operation.
      
      Addressed an issue where the SMBIOS type 38 offset 0x10 had an incorrect
      value.
      
      Addressed an issue where the erase status for SATA drives is reported
      incorrectly when using One Button Secure Erase.
      
      Addressed an issue where location information under RBSU "Storage Device
      Information" page will show "null string" when VROC is enabled.
      
      Addressed an issue where the "Minimum Processor Idle Power Core C-state" from
      RBSU showed an incorrect value when one of "Virtualization - Max Performance",
      "Low Latency", "Transactional Application Processing", "High Performance
      Compute (HPC)" workload profiles is selected.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages were
      not synchronized.
      
      Addressed an issue where an incorrect "processor's PUcode" version showed up
      on screen during the POST after downgrading the System ROM.
      
      Addressed an issue where status display of PCIe Root Complex for Intel Quick
      Assist Technology (Intel QAT) is not correct in Windows Device Manger on dual-
      processor systems.
      
      Addressed an issue where the PCI speed might be incorrect when setting
      "Maximum PCI Express Speed" to "Per Port Control".
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.44_07-31-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Address an issue with 4th Generation Intel Xeon Processors that can result in
      an unexpected reset with a machine check error logged to the Integrated
      Management Log (IML). This issue is not unique to HPE systems. The following
      is Intel's description of the issue: "Under a complex microarchitectural
      conditions, a hold time violation in the uncore may affect the traffic flowing
      from the Intel Ultra Path Interconnect (UPI) back to a Caching Home Agent
      (CHA) causing a CHA Table of Requests (TOR) timeout (TO) machine check
      exception (MCE) to occur. Due to this erratum, the system may hang." This
      version of the System ROM will update internal code in all installed
      processors when the system boots. This code internal to the processors will
      not be downgraded if the System ROM is downgraded. It is not supported to have
      processors installed with different versions of this internal code.
      
      Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded
      from PCIe Generation 5 to Generation 4.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.44_07-31-2023
changelog:
  -     Set the value of the Snoop Response Hold Off for IOAT Stack setting to 7 when
      the vRAN Workload Profile has been selected. This aligns with Intel's
      performance tuning recommendation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.44_07-31-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Address an issue with some 4th Generation Intel Xeon Processors that can
      result in an unexpected reset with a machine check error logged to the
      Integrated Management Log (IML).  This issue is not unique to HPE systems.
      The following is Intel's description of the issue:  "Under complex
      microarchitectural conditions, the processor may experience a Caching Home
      Agent Table of Requests (TOR) timeout machine check exception."  This version
      of the System ROM will update internal processor firmware during boot.  This
      internal processor firmware cannot be downgraded even if the System ROM is
      downgraded. Using processors with different version of internal firmware is
      not supported.
      
      Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded
      from PCIe Generation 5 to Generation 4.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.46_09-26-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the MegaRAID controller status is displayed as
      "unknown" on the iLO web page.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.48_10-19-2023
changelog:
  -     Replaced "AC power" with "external power" in the help text of "Automatic
      power-on" option. This is due to ProLiant server also provides the DC power
      supply option.
      
      Added new Microsoft secure boot keys, KEK2023, Microsoft UEFI CA 2023 and
      Windows UEFI CA 2023, since the original keys will expire in 2026.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.48_10-19-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system might hang with SRIS of CPU PCIe port enabled.
      
      Addressed an issue where iLO web would not display the PCIe device installed
      on Slot 8 when the configuration includes a tertiary riser and Slot 8 is PCI
      Express x8.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10_11-28-2023
changelog:
  -     Added support for the 5th Gen Intel Xeon Scalable Processors.
      
      Added Maximum Memory Bus frequency support to 5600 MT/s for the 5th Gen Intel
      Xeon Scalable Processors.
      
      Added support for NVMe over Fabrics.
      
      Added new System Configuration (RBSU) configuration options that allow the
      system not to create boot options for non-bootable fixed drive.
      
      Modified System Configuration (RBSU) configuration options that support new
      license SKU "RAID1 Only" and drop "Standard" SKU for Intel VROC.
      
      Enhanced the warning messages of "Embedded SATA Configuration" options in
      RBSU.
      
      Enhanced the warning messages of "Intel CPU VMD Support" options in RBSU.
      
      Added new System Configuration (RBSU) configuration options that could control
      Intel Trust Domain Extension (TDX) functions.
      
      Added new System Configuration (RBSU) configuration options that could control
      the NVMe-oF Software Initiator.
      
      Added new System Configuration (RBSU) configuration options that could control
      the PCI-E Data Link Feature Exchange.
      
      Added new System Configuration (RBSU) configuration options that allow Power
      Supply Unit fan control.
      
      Enhanced the help message for System Configuration (RBSU) configuration
      options for Automatic Power-On.
      
      Enhanced the help message and status information for System Configuration
      (RBSU) configuration options for HBM Memory Mode.
      
      Updated the Processor Capability Indicator in SMBIOS type 197.
      
      Enhanced POST messages in situations where where unsupported processors are
      installed.
      
      Added PCIe Gen2 device in SMBIOS type 9.
      
      Enhanced SMBIOS type 9 for PCIe retimer device information.
      
      Displayed the information of first device in SMBIOS type 203 when the PCI slot
      is bifurcated.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10_11-28-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.005.0 (2.10_11_09_2023).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue where system would reboot when hot-added NVMe drives in Linux
      with Intel VMD Support enabled.
      
      Fixed an issue where SMBIOS type 219 showed incorrect feature flags when the
      Intel Xeon CPU Max Series processors are installed.
      
      Fixed an issue where PCIe fatal error reporting function did not respond
      correctly.
      
      Fixed an issue where Intel TSX Support could not be set with enabled state.
      
      Fixed an issue where the x2APIC is not enabled for 64-core processors.
      
      Fixed an issue where the PCIe correctable error message was not displayed in
      Integrated Management Log (IML).
      
      Fixed an issue where the OCP retimer slot number was not correctly reported in
      SMBIOS type 216.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.12_12-13-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.005.0 (2.10_11_09_2023).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue where Intel Software Guard Extensions (SGX) Attestation may
      fail on the 5th Generation Intel Xeon Scalable Processors. Software Guard
      Extensions (SGX) is disabled by default.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.16_03-01-2024
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This revision of the System ROM includes the revision of the TPM2 Measure boot
      library update which provides mitigation for security vulnerabilities
      documented as CVE-2022-36763 and CVE-2022-36764.
      
      This revision of the System ROM includes the revision of the MiniZip Library
      update which provides mitigation for security vulnerabilities documented as
      CVE-2023-45853.
      
      This revision of the System ROM includes the revision of the EDK2 NetworkPkg
      IP stack implementation update which provides mitigation for security
      vulnerabilities documented as CVE-2023-45229, CVE-2023-45230, CVE-2023-45231,
      CVE-2023-45232, CVE-2023-45233, CVE-2023-45234, CVE-2023-45235,
      CVE-2023-45236, CVE-2023-45237.
      
      Addressed an issue where PCI slot information, Slot Physical width and Slot
      Pitch are not correct in the SMBIOS Type 9.
      
      Addressed an issue where the NUMA nodes are not assigned properly when Sub-
      NUMA Clustering is set 2 or 4.
      
      Addressed an issue where the operating system cannot detect the iSCSI hard
      drive through IPv6 installation.
      
      Addressed an issue where the version information of the System Programmable
      Logic Device may be displayed incorrectly in RBSU and iLO GUI.
      
      Addressed an issue where a Red Screen of Death (RSOD) may be seen during a
      system boot.
      
      Addressed an issue where the embedded NIC(Network Interface Card) connected to
      the Intel PCH could become missing when Intel(R) PCH VMD Support is set to
      enabled.
      
      Addressed an issue where the "Enabled Cores per Processor" in RBSU cannot be
      set greater than 56.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.16_03-01-2024
changelog:
  -     Added help messages about using the "-tpmbypass" flag when flashing smart
      components under silent mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_05-27-2024
changelog:
  -     Added production HCI marker key for OEM activation for Windows Azure.
      
      Added value "C6 without C1E" in System Configuration (RBSU) option "Power
      Management/Advanced Power Options menu/Minimum Processor Idle Power Core
      C-State". When selected, the Minimum Processor Idle Power Core C-State is C6
      with C1E disabled. This setting has the following Redfish property:
      /redfish/v1/systems/1/bios/MinProcIdlePower
      
      Added the System Configuration (RBSU) option "Power and Performance
      Options/Advanced Performance Tuning Options/Intel(R) AVX License Pre-Grant
      Override". When enabled, the pre-grant license level will be set based on the
      value of AVX ICCP Pre-Grant Level option. This setting has the following
      Redfish property:
      /redfish/v1/systems/1/bios/settings/AvxLicensePreGrantOverride
      
      Added the System Configuration (RBSU) option "Power and Performance
      Options/Advanced Performance Tuning Options/Intel(R) AVX ICCP Pre-Grant Level"
      to pre-grants an AVX level to the core. This setting has the following Redfish
      property: /redfish/v1/systems/1/bios/settings/AvxIccpPreGrantLevel
      
      Added the System Configuration (RBSU) option "PCIe Device
      Configuration/Advanced PCIe Configuration/ PCI-E ASPM Support (Global)" to
      control ASPM support in all PCIe root port. This setting has the following
      Redfish property: /redfish/v1/systems/1/bios/settings//redfish/v1/systems/1/bi
      os/settings/PcieGlobalAspm


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.18_03-27-2024
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the power supply unit redundancy function operated
      abnormally.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.18_03-27-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.005.0 (2.10_11_09_2023)
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the power supply unit redundancy function operated
      abnormally.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.22_06-19-2024
changelog:
  -     See the release document U57_2.22_06_19_2024 in Download Product Binaries page
      from Product Summary of the firmware product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.50_04-22-2025
changelog:
  -     Disabled AMP Prefetch for 'vRAN' Workload Profile to aligned with Intel BIOS
      Settings for FlexRAN v2.0.
      
      Added help text for "Smooth Cooling" in system configuration (RBSU) option.
      
      Introduced an enhancement to prevent potential system shutdowns caused by
      specific CPU temperature errors.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40_06-29-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where a drive cannot be unmounted after hot-plug
      interruption during DPC (Downstream Port Containment) recovery process under
      VMware.
      
      Addressed an issue where Citrix HyperVisor could not be installed.
      
      Addressed an issue where the system would hang in POST if Intel UPI link
      enablement was set to single link operation.
      
      Addressed an issue where the SMBIOS type 38 offset 0x10 had an incorrect
      value.
      
      Addressed an issue where the erase status for SATA drives is reported
      incorrectly when using One Button Secure Erase.
      
      Addressed an issue where location information under RBSU "Storage Device
      Information" page will show "null string" when VROC is enabled.
      
      Addressed an issue where the "Minimum Processor Idle Power Core C-state" from
      RBSU showed an incorrect value when one of Virtualization Max Performance, Low
      Latency, Transactional Application Processing, High Performance Compute (HPC)
      workload profiles is selected.
      
      Addressed an issue where the TPM status between RBSU and iLO web pages were
      not synchronized.
      
      Addressed an issue where an incorrect "processor's PUcode" version showed up
      on screen during the POST after downgrading the System ROM.
      
      Addressed an issue where status display of PCIe Root Complex for Intel Quick
      Assist Technology (Intel QAT) is not correct in Windows Device Manger on dual-
      processor systems.
      
      Addressed an issue where the PCI speed might be incorrect when setting
      "Maximum PCI Express Speed" to "Per Port Control".
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.44_07-31-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Address an issue with 4th Generation Intel Xeon Processors that can result in
      an unexpected reset with a machine check error logged to the Integrated
      Management Log (IML). This issue is not unique to HPE systems. The following
      is Intels description of the issue: Under a complex microarchitectural
      conditions, a hold time violation in the uncore may affect the traffic flowing
      from the Intel Ultra Path Interconnect (UPI) back to a Caching Home Agent
      (CHA) causing a CHA Table of Requests (TOR) timeout (TO) machine check
      exception (MCE) to occur. Due to this erratum, the system may hang. This
      version of the System ROM will update internal code in all installed
      processors when the system boots. This code internal to the processors will
      not be downgraded if the System ROM is downgraded. It is not supported to have
      processors installed with different versions of this internal code.
      
      Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded
      from PCIe Generation 5 to Generation 4.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.44_07-31-2023
changelog:
  -     Set the value of the Snoop Response Hold Off for IOAT Stack setting to 7 when
      the vRAN Workload Profile has been selected. This aligns with Intels
      performance tuning recommendation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.48_09-27-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system might hang with SRIS of CPU PCIe port enabled.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.12_12-19-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.005.0 (2.10_11_09_2023).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue where Intel Software Guard Extensions (SGX) Attestation may
      fail on the 5th Generation Intel Xeon Scalable Processors. Software Guard
      Extensions (SGX) is disabled by default.
      
      Corrected the default of Workload Profile to be General Power Efficient
      Compute in the ROM-Based Setup Utility (RBSU).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.14_01-02-2024
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue where the OCP Slot 14 device was not displayed properly and the
      OCP Slot 21 became redundant from iLO web.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.46_02-21-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.075.0 (2.40_10_23_2024).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when both TXT and TDX are
      enabled.
      
      Addressed an issue where the system might fail to update NVMe drive firmware.
      
      Addressed an issue where the system might not be able to detect disk removal
      via NVMe-oF during VMware installation.
      
      Addressed an unexpected fan control issue that triggered sustained high speeds
      on Alletra 4120 LFF SKU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.36_05-26-2023
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Added new System Configuration (RBSU) configuration options that allow
      controlling Intel OSB function. This includes the "OSB Local/Remote Read"
      option with settings of "Disabled" (default) and "Auto" options that allows
      setting Intel Opportunistic Snoop Broadcast.  When the "OSB Local/Remote Read"
      option is configured for "Disabled", BIOS will disable OSB function. When the
      "OSB Local/Remote Read" option is configured for "Auto", BIOS will
      automatically decides based on silicon compatibility. In System Configuration
      (RBSU), these options are located under the BIOS/Power and Performance
      Options/Intel UPI Options. This setting has the following Redfish properties:
      /redfish/v1/systems/1/bios/settings/OsbLocalRemoteRead
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10_11-28-2023
changelog:
  -     Added support for NVMe over Fabrics.
      
      Added new System Configuration (RBSU) configuration options that allow the
      system not to create boot options for non-bootable fixed drive.
      
      Modified System Configuration (RBSU) configuration options that support new
      license SKU "RAID1 Only" and drop "Standard" SKU for Intel VROC.
      
      Enhanced the warning messages of "Embedded SATA Configuration" options in
      RBSU.
      
      Enhanced the warning messages of "Intel CPU VMD Support" options in RBSU.
      
      Added new System Configuration (RBSU) configuration options that could control
      Intel Trust Domain Extension (TDX) functions.
      
      Added new System Configuration (RBSU) configuration options that could control
      the NVMe-oF Software Initiator.
      
      Added new System Configuration (RBSU) configuration options that could control
      the PCI-E Data Link Feature Exchange.
      
      Added new System Configuration (RBSU) configuration options that allow Power
      Supply Unit fan control.
      
      Enhanced the help message for System Configuration (RBSU) configuration
      options for Automatic Power-On.
      
      Enhanced the help message and status information for System Configuration
      (RBSU) configuration options for HBM Memory Mode.
      
      Updated the Processor Capability Indicator in SMBIOS type 197.
      
      Enhanced POST messages in situations where where unsupported processors are
      installed.
      
      Added PCIe Gen2 device in SMBIOS type 9.
      
      Enhanced SMBIOS type 9 for PCIe retimer device information.
      
      Displayed the information of first device in SMBIOS type 203 when the PCI slot
      is bifurcated.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.12_12-13-2023
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.01.04.005.0 (2.10_11_09_2023).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Fixed an issue where Intel Software Guard Extensions (SGX) Attestation may
      fail. Software Guard Extensions (SGX) is disabled by default.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.44_01-18-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel MR1
      Best Known Configuration for Intel Xeon E-2400 series processors. This
      revision of the System ROM includes the mitigation for NetworkPkg PXE IP stack
      vulnerabilities documented as CVE-2023-45229, CVE-2023-45230, CVE-2023-45231,
      CVE-2023-45232, CVE-2023-45233, CVE-2023-45234, CVE-2023-45235,
      CVE-2023-45236, and CVE-2023-45237.
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.02.04.016.0 (1.44_01_03_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the SATA drive location information was inconsistent
      between One-time boot menu and SMBIOS table.
      
      Addressed an issue where iSCSI SW ipv6 HDD was not detected under OS when the
      iSCSI IpAddressType was set to auto.
      
      Addressed an issue where the PMC version presented even when RPSU was not
      installed.
      
      Addressed an issue where DMI Link ASPM was not set correctly.
      
      Addressed an issue where Enhanced C-State could not be disabled when Minimum
      Processor Idle Power Core C-State was enabled.
      
      This revision of the System ROM includes the mitigation for NetworkPkg PXE IP
      stack vulnerabilities documented as CVE-2023-45229, CVE-2023-45230,
      CVE-2023-45231, CVE-2023-45232, CVE-2023-45233, CVE-2023-45234,
      CVE-2023-45235, CVE-2023-45236, and CVE-2023-45237.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.46_02-22-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2023-45229, CVE-2023-45853, CVE-2022-36763 and
      CVE-2022-36764. This version of the System ROM should be paired with Server
      Platform Services (SPS) Firmware 06.02.04.016.0 (1.44_01_03_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system would reboot immediately after changing
      Intel TXT setting then pressing F10.
      
      Addressed an issue where the boot order of NVMe drives is always the lowest
      prioirty.
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2023-45229, CVE-2023-45853, CVE-2022-36763 and
      CVE-2022-36764.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.48_03-14-2024
changelog:
  -     *Important Notes:**
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727. This version of
      the System ROM should be paired with Server Platform Services (SPS) Firmware
      06.02.04.016.0 (1.44_01_03_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Redfish resource was not updated after deleting
      secure boot keys via System Configuration (RBSU).
      
      Addressed an issue where the system failed to enroll certificate to PK and KEK
      via Redfish.
      
      This revision of the System ROM includes the mitigation for vulnerabilities
      documented as CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.50_05-16-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel MR2
      Best Known Configuration for Intel Xeon E-2400 series processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may hang while enrolling secure boot key dbr
      certificate via Redfish API.
      
      Addressed an issue where system failed to boot with selected NVMe HDD by
      setting One-Time Boot Option in ILO Web.
      
      Addressed an issue where the boot order was cleared unexpectedly after
      configuring System Configuration (RBSU) options, navigating to Boot Options >
      UEFI Boot Settings > UEFI Boot Order, and then pressing F12 to Save and Exit.
      
      Removed the value of "Not Specified" in System Configuration (RBSU) option
      "Server Security/Trusted Platform Module Options/Current TPM 2.0 Active PCRs"
      and set the default value as "SHA1 and SHA256".
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.52_07-11-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.02.04.035.0 (1.50_04_10_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where duplicated and incorrect task status were logged iLO
      Event Log.
      
      Addressed an issue where multiple KEK instances appeared after enrollment of
      KEK certificate from Redfish API.
      
      Addressed an issue where dbr were not deleted after deleting all keys via
      Redfish API.
      
      Addressed an issue where Negotiated Link Width in RBSU showed incorrect
      information after configurating bifurcation.
      
      Addressed an issue where system may encounter RSOD after enrollment of an
      improper certfifcate.
      
      Addressed an issue where the Logical Drive name was cleared in RBSU after
      leaving configuration page of MR controller.
      
      Addressed an issue that Battery Failure IML message log may be incorrectly
      logged for MR Controller with Smart Storage Battery.
      
      Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword
      may not work.
      
      Addressed a secure boot database synchronizing issue via Redfish API.
      
      Addressed an issue where system may encounter a RSOD while updating SAS drive
      FW via HPE Service Packs, including, but not limited to, VMware ESXi Online
      HDD FW Component Bundle 16.00, HPE Synergy Service Pack (SSP) 2024.01.02
      (January 2024) and the future HPE Synergy Service Pack (SSP) 2024.07.01 (July
      2024).
      
      Addressed an issue where updating NVMe-oF initiator name would not take
      effect.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_09-05-2024
changelog:
  -     Added Redfish API for Boot Progress.
      
      Updated Chinese and Japanese translation.
      
      Added the System Configuration (RBSU) option "Network Options/NVMe-oF
      Configuration". This setting has the following Redfish property:
      
      /redfish/v1/systems/1/Bios/oem/hpe/nvmeof/


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.60_09-05-2024
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Catlow
      PLR1 guidance. This version of the System ROM should be paired with Server
      Platform Services (SPS) Firmware 06.02.04.042.0 (1.60_09_05_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where One button secure erase (OBSE) report may show
      incorrect Drive Port Number and Box Number for MicroChip SR controllers.
      
      Addressed an issue where system may stuck after enrolling many certificates
      and signatures.
      
      Addressed an issue where Driver Health Message may show twice in POST when
      drive is removed and cold boot.
      
      Addressed an issue where NS204i may not be identified as NVMe device.
      
      Addressed an issue where the virtual serial port may still have message output
      when the serial port is set to 'Disabled' or 'Physical Port'.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10_12-06-2024
changelog:
  -     *Important Notes:**
      
      This is the initial version to support Intel Xeon 6300 series processors. This
      version of the System ROM contains updates aligned with the Intel Catlow
      Refresh BKC CWL.1.A.4420.00 This version always set "RBSU\Power and
      Performance option\Enhance C state" to "Enabled" to mitigate processor Vmin
      shift instability issue per Intels recommendation.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where some strings of "NVMe-oF Configuration and Attempt
      pages" in system RBSU menu are still in English after switching the language
      to non-English version.
      
      Addressed an issue where system RBSU menu might list duplicate or incorrect
      network interfaces in the selection page.
      
      Addressed an issue where the system RBSU menu might not display clear drive
      location information.
      
      Addressed an issue where the "Server Boot Order" in iLO web is not aligned
      with "UEFI Boot Order Control" in RBSU
      
      Addressed an issue where an error message in Linux would indicate TCG log size
      is not compatible.
      
      Addressed an issue where the "Pending Change light" may be on even if there is
      no option has been modified in RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10_12-06-2024
changelog:
  -     This version always set "RBSU\Power and Performance option\Enhance C state" to
      "Enabled" to mitigate processor Vmin shift instability issue per Intel's
      recommendation.
      
      Added new Microsoft Option Rom UEFI CA 2023 secure boot key.
      
      Added "Smooth Cooling option" in the RBSU\Advanced Options\Fan and Thermal
      Options.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10_12-06-2024
changelog:
  -     *Important Notes:**
      
      This is the initial version to support Intel Xeon 6300 series processors. This
      version of the System ROM contains updates aligned with the Intel Catlow
      Refresh BKC CWL.1.A.4420.00.
      
      This version always set "RBSU\Power and Performance option\Enhance C state" to
      "Enabled" to mitigate processor Vmin shift instability issue per Intel's
      recommendation.
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.03.04.048.0 (2.10_12_03_2024).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where some strings of "NVMe-oF Configuration and Attempt
      pages" in system RBSU menu are still in English after switching the language
      to non-English version.
      
      Addressed an issue where system RBSU menu might list duplicate or incorrect
      network interfaces in the selection page.
      
      Addressed an issue where the system RBSU menu might not display clear drive
      location information.
      
      Addressed an issue where the "Server Boot Order" in iLO web is not aligned
      with "UEFI Boot Order Control" in RBSU.
      
      Addressed an issue where an error message in Linux would indicate TCG log size
      is not compatible.
      
      Addressed an issue where the "Pending Change light" may be on even if there is
      no option has been modified in RBSU.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.12_02-21-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Catlow
      Refresh BKC CWL.1.A.4420.00. This version of the System ROM should be paired
      with Server Platform Services (SPS) Firmware 06.03.04.048.0 (2.10_12_03_2024).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the PSU fan keeps running at high speed after system
      shutdown.
      
      Addressed an issue where system may fail to update NVMe drive firmware.
      
      Addressed an issue where NvmeOf system may not be detected during VMWare
      installation.
      
      Addressed an issue where the maximum frequency of the processor shows
      incorrectly after enable or disable Intel Turbo Boost.
      
      Addressed an issue where the system would use UUID for IPV6 DHCP when
      "RBSU\Network Options\Network Boot Options\IPv6 DHCP Unique Identifier\DUID-
      LLT" is selected.
      
      Addressed an issue where the Consistent Device Naming (CDN) may not work.
      
      Addressed an issue where the RBSU value is not aligned with the actual C1E
      setting.
      
      Addressed an issue where the system might bring up a warning message ("ERST:
      [Firmware Warn]: too many record IDs!") in the Linux environment during boot
      up.
      
      Updated SMBIOS type 4 processor max speed to 5700 MHz.
      
      Addressed an issue where the PSU fan would keep running at high speed after
      system shutdown.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.14_03-11-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM should be paired with Server Platform Services
      (SPS) Firmware 06.03.04.048.0 (2.10_12_03_2024).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system might RSOD when performing firmware update
      via Firmware Management Protocol.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.20_03-21-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Catlow
      Refresh MR1 BKC. This version of the System ROM should be paired with Server
      Platform Services (SPS) Firmware 06.03.04.058.0 (2.20_03_03_2025).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system may encounter RSOD and fail to update
      firmware while performing firmware update.
      
      Addressed an issue where the system may encounter RSOD if NVMe-oF target did
      not have partitions.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.22_05-16-2025
changelog:
  -     *Important Notes:**
      
      This version of the System ROM contains updates aligned with the Intel Catlow
      Refresh MR1 BKC. This version of the System ROM should be paired with Server
      Platform Services (SPS) Firmware 06.03.04.058.0 (2.20_03_03_2025).
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the Name field of the Logical Drive under MR
      controller page might be missing or changed unintentionally after exiting and
      going back to the MR controller page.
      
      Addressed an issue where the messages of "HPE Intelligent Provisioning" is
      incorrect for OEM customers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.04.033.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains updates
      aligned with the Intel Best Known Configuration (BKC) WW09.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Updated Server Platform Services (SPS) Firmware to 06.00.04.033.0 to align
      with the Intel Best Known Configuration (BKC) WW09.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.04.075.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for Intel Sapphire Rapids.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version contains the latest Server Platform Services firmware for Intel
      Sapphire Rapids.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.00.05.046.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th Generation Intel Xeon Scalable Processors.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      This version contains the latest Server Platform Services firmware for 4th
      Generation Intel Xeon Scalable Processors.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.005.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th Generation Intel Xeon Scalable Processors and 5th
      Generation Intel Xeon Scalable Processors. This version of the SPS should be
      paired with System ROM 2.10 (11/28/2023).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may enter standby mode on Power-On Self-Test
      (POST) during warm reset cycle.
      
      Addressed an issue where system may stop responding at "Memory Initialization
      - Start" during Power-On Self-Test (POST).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.005.0-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 06.01.04.005.0(B) contains updates to the firmware packaging and is
      functionally equivalent to ver. 06.01.04.005.0. It is not necessary to upgrade
      with Revision B if a previous component revision was used to upgrade the
      firmware to version 06.01.04.005.0.
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th Generation Intel Xeon Scalable Processors and 5th
      Generation Intel Xeon Scalable Processors. This version of the SPS should be
      paired with System ROM 2.10 (11/28/2023) or later.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where systems may enter standby mode in Power-On Self-Test
      (POST) during warm reset cycle.
      
      Addressed an issue where systems may stop responding at "Memory Initialization
      - Start" during Power-On Self-Test (POST).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.01.04.005.0-2.1
changelog:
  -     *Important Notes:**
      
      Ver. 06.01.04.005.0(B) contains updates to the firmware packaging and is
      functionally equivalent to ver. 06.01.04.005.0. It is not necessary to upgrade
      with Revision B if a previous component revision was used to upgrade the
      firmware to version 06.01.04.005.0.
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for 4th Generation Intel Xeon Scalable Processors and 5th
      Generation Intel Xeon Scalable Processors. This version of the SPS should be
      paired with System ROM 2.10 (11/28/2023).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where system may enter standby mode on Power-On Self-Test
      (POST) during warm reset cycle.
      
      Addressed an issue where system may stop responding at "Memory Initialization
      - Start" during Power-On Self-Test (POST).
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.02.04.016.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for the Intel Raptor-Lake PCH-S based systems. This version of
      the SPS should be paired with System ROM 1.44 (01/18/2024) or later.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version contains the latest Server Platform Services firmware for the
      Intel Raptor-Lake PCH-S based systems.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.02.04.035.0
changelog:
  -     This version contains the latest Server Platform Services firmware for the
      Intel Xeon E-2400 series processors.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.02.04.035.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for the Intel Xeon E-2400 series processors. This version of
      the SPS should be paired with System ROM 1.50 (05/16/2024) or later.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Intel(R) SPS Firmware may assign duplicate MCTP EIDs
      for adapters.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.02.04.042.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for the Intel Xeon E-2400 series processors. This version of
      the SPS should be paired with System ROM 1.60_09-05-2024.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version contains the latest Server Platform Services firmware for the
      Intel Xeon E-2400 series processors.
      
      This version is in compliance with Intel PLR1 guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.03.04.048.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for the Intel Xeon E-2400 series processors. This version of
      the SPS 06.03.04.048.0 (2.10_12_03_2024) should be paired with System ROM
      2.10_12-06-2024.
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      This version is in compliance with Intel Catlow RPL-E PLR2 and Intel Catlow
      RPL-E Refresh PV guidance.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 06.03.04.058.0
changelog:
  -     *Important Notes:**
      
      This version of the Server Platform Services (SPS) Firmware contains the
      latest package for the Intel Xeon E-2400 series processors. This version of
      the SPS 06.03.04.058.0 (2.20_03_03_2025) should be paired with System ROM
      2.20_03-21-2025.
      
      Details about reported security vulnerabilities and their mitigation can be
      found at the following link [Security Bulletin Library | HPE Support](https://
      support.hpe.com/connect/s/securitybulletinlibrary?language=en_US).
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where the system may encounter reset loop after updating
      ME/SPS firmware using smart components.
      
      **Known Issues:**
      
      None


